A source produces independent symbols from an alphabet of three letters. Each source symbols can be A,B or C with respective probability 0.5, 0.25 and 0.25. (a) What is the source entropy H? (b) Find a Huffman code for the individual letters of the source alphabet. What is the average number of bits per symbol for this code? (c) You are asked to design a code for blocks od of two symbols from the source at a time. The alphabet for this extended source is of size 9. tai woda odien

A source produces independent symbols from an alphabet of three letters. Each source symbols can be A,B or C with respective probability 0.5, 0.25 and 0.25. (a) What is the source entropy H? (b) Find a Huffman code for the individual letters of the source alphabet. What is the average number of bits per symbol for this code? (c) You are asked to design a code for blocks od of two symbols from the source at a time. The alphabet for this extended source is of size 9. tai woda odien

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HW 2_2 The volume of a partially-filled spherical tank can be computed as: V = πα 3 (3R – d); where d is the depth of the water in the tank (m) and R is the radius of the tank (m). Given that R=3m, to what depth must the tank be filled so that it holds 30 m³? Write a PYTHON code & implement the bisection algorithm to answer the question correct to 3 sig figs. Plot to select your own initial guesses. Display the answer in an informative sentence, using formatted printing.
I was wondering if anyone can help me understand the question and answer.
using matlab: 1. Write a code that demonstrates sin2(x) + cos2(x) = 1 with different values. Assign: x1 = pi/6 x2 = pi/4 x3 = pi/3 and test all values.
i need the answer quickly
I need a clear step by step answer please with the simplest method :) Thank you
I wanted to know how to create plots like these in MATLAB. I belive they were called herpolhode plots.
Please help me, please, I want to solve all the questions, without quoting and without plagiarism, I want the solution in MS Word, I do not want handwriting...
hey can i get help with these two questions please. thank you.
In your biomechanical testing lab, you perform a series of compression tests to determine the relationship between apparent bone density (p, units of g/cm³) and ultimate stress (ơult, units of MPa). Using the set of experimental measurements below, write an m-file to fit a power relationship of the form O uli = Ap to the data. Use the log transform method to linearize the system and data, followed by linear regression. Plot the data points and the power relationship on a single plot. Be sure to label your axes and provide a legend. Provide a printout of your m-file and a printout of the command window showing your results. Write down the best fit equation and box it. 8.76 5.25 4.26 5.51 3.88 18.45 2.09 13.72 5.42 2.17 Oult (MPa) p (g/cm³) 0.598 | 0.459 0.319 | 0.235 0.141 0.754 0.177 0.553 0.394 0.246
A single degree-of-freedom linear elastic structure was subjected to a series of harmonic excitations, one at a time. The excitations had the same forcing magnitude but different forcing frequency. Forcing frequencies and observed peak steady-state displacements are shown in the graph below. Find the natural period and damping ratio of the structure. Displacement (mm) 60 50 40 30 20 10 0 0 1 2 . 3 4 Forcing frequency, f [Hz] 5 4. 6 7
The rapid progress of engineering design and information technology has caused difficulties in analyzing system reliability. Because of the increased complexity in system reliability structure (component/subsystem interfaces), many unexpected failure modes could occur, and their behaviors are interdependent. At a system’s design and development stage, the main challenge in analyzing a complex system is the failure uncertainty introduced by the incomplete knowledge of the system. This makes it hard to decompose system reliability into subsystem/component reliability in a deterministic manner, such as series or parallel systems. As a result, some common reliability analysis tools such as fault tree (FT) and reliability block diagram (RBD) become inadequate. Do you agree, why or why not? Are there any other approaches to system reliability assessment beside these tools at the early system’s design and development stage (what are these approaches)?