A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ (πd3). Using a material strength of 172.4 MN/m2 and a design factor of 2.5, determine the minimum diameter of the rod. Using Table 1, select a preferred fractional diameter and determine the resulting factor of safety

A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ (πd3). Using a material strength of 172.4 MN/m2 and a design factor of 2.5, determine the minimum diameter of the rod. Using Table 1, select a preferred fractional diameter and determine the resulting factor of safety

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.21P: A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular...

See similar textbooks

Related questions

Q: A simply supported beam of circular cross-section made up of hot rolled steel is subjected to a…

A: The ultimate aim of the design is to prepare a drawing or chart in such a way that the resulting…

Q: This problem illustrates that the factor of safety for a machine element depends on the particular…

A: Given, AISI 1006 cold drawn steel, F = 0.55 N, P = 4.0 kN, T = 25 Nm, yield stress, Sy = 280 MPa, D…

Q: The plate of the figure is subjected to a bending moment with irregular cycles, which are repeated.…

A: NOTCH SENSITIVITY FACTOR(q) It is defined as the susceptibility of a material to succumb to the…

Q: A simply supported shaft is shown. A constant magnitude distributed unit load p is applied as the…

A: Given: The safety factor, n = 2 The ultimate strength, Sut = 745 MPa The yield strength, Sy = 427…

Q: Two metal plates, are joined as show below. Using standard material values, complete the following:…

A: To Find : The suitable diameter , Given : The load is P=150kN. The shear strenght of aluminium is…

Q: The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches.…

Q: luminum 6061 T4, and a ss section areas of 1 in^2. laced on each of the bars AISI 4130 Steel

A: AISI 4130 steelAluminum 6061 T4Ti-6AAL-4VArea=1in2Axial-Stress=15ksi To-Find:- The bar will be more…

Q: Calculate the mean stress in N/mm2 and variable stress in N/mm2 ii) Calculate the Ultimate…

A: For solution refer below images.

Q: A simply supported beam of circular cross-section made up of hot rolled steel is subjected to a…

A: The question is about fluctuating loads. Fluctuating loads induce fluctuating stresses on the…

Q: Determine the width and thickness of the leaves (in mm) of a leaf spring using the following…

Q: A simply supported beam of circular cross-section made up of hot rolled steel is subjected to a…

A: The fluctuating loads on a beam induce fluctuating stresses, which in turn lead to fatigue failure.…

Q: A cylindrical 1045 steel bar is subjected to repeated compression-tension stress cycling along its…

Q: 1. A piston rod, made of AISI 3140 steel, OQT 1000 F, is subjected to a repeated, reversed load. The…

Q: Calculate the mean stress in N/mm2 and variable stress in N/mm2 ii) Calculate the Ultimate…

A: For solution refer below images.

Q: The figure below is subjected to a load fluctuating between Pmin and Pmax. Calculate the factor of…

A: Write the given values along with the suitable variables.

Q: Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the…

A: The information provided in the image includes:Maximum cylinder pressure: 3.15 N/mm²Cylinder bore:…

Q: A simply supported beam of circular cross-section made up of hot rolled steel is subjected to a…

A: Given, σmax=82 N/mm2σmin=-42 N/mm2 FOS=2 syt=0.55sutse=0.45sut

Q: A steel rod is subjected to a reversed axial load of 180 kN. Find the diameter of the rod for a…

Q: A part is loaded with a combination of bending, axial, and torsion such that the following stresses…

A: Given:The material properties are .The adjusted endurance limit is .The fatigue stress concentration…

Q: If a solid circular rod having an initial diameter D = 0.03 m and initial length L = 0.8 m, is…

A: Given: Initial Diameter of the solid circular rod, Di=0.03m Initial length of the solid circular…

Q: factor of safet

A: d= 40mmF = 29KNL = 796mmT = 1.7KNmfail stress = 156MPamaterial- brittle cast iron

Q: Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading…

A: Given, Shaft diameter, d=20 mm=0.020 m Shaft length, L=120 mm=0.12 m F1=750 N F2=3000 N Torsion,…

Q: A solid circular rod of diameter d undergoes a bending moment M=1300 lbf-in inducing a stress o=32…

A: For given rod stress, σ=Snd32(1300)πd3=250002.5d=1.098 in so, minimum diameter will be 1.098 in

Q: Use F.S. 2 against buckling. (Eigure 1) Part A It P-20 kip, determine the required minimum diameter…

Q: What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application…

Q: 00 N/mm2 is acting on 55 mm diameter steel. The u e 1. Calculate the life of the bar for the…

Q: N for Newton, m for meter, mm for millimeter, N/(mm^2) for Stress, mm^2 or m^2 for Area, mm^4…

Q: steel is subjected to a fluctuating load that varies from -F to +3F. Determine the minimum ultimate…

Q: Að 62⁰ & PO 00 www. OB 19⁰

Q: Q2: A cold drawn steel rod of circular cross- section is subjected to a variable bending moment of…

A: Calculate the mean bending moment,…

Q: A bar is subjected to fluctuating tensile load from 20 KN to 100 kN. The material has yield strength…

A: Given, Minimum force during a cycle = Fmin = 20 kN Maximum force during a cycle = Fmax = 100 kN…

Q: A steel rod of diameter D = 50 mm has a tensile yield strength of 345 MPa supports an axial load P =…

Q: The design of the crank for a shredder is shown below. The applied force P on the handle is 200 N…

A: given; x=200mmP=200Ndiameter of shaft=dstress concentration factor =2.5design factor=3

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading conditions according to the Maximum shear stress hypothesis and the Maximum strain energy hypothesis. Shaft diameter: 20 mm, Shaft Length 120 mm, F1 = 750N, F2 = 3000N, Mb = 2400 N.mm. Steel if St37 and Safety coefficient is 2 If taken, will this stick work safely under these operating conditions? (Yield of given steel Strength 225 Mpa, Tensile strength 370 Mpa)
A steel rod is subjected to a reversed axial load of 180 kN. Find the diameter of the rod for a factor of safety of 2. Neglect column action. The material has an ultimate tensile strength of 1070 MPa and yield strength of 910 MPa. The endurance limit in reversed bending may be assumed to be one-half of the ultimate tensile strength. Other correction factors may be taken as follows: For axial loading (Ka) = 0.7; For machined surface (Ksur) = 0.8 ; For size (Ksz) = 0.85 ; For stress concentration(Kf)= 1.0.3.