A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P |1 Strain gage- d D E 2 H b Answer: P= i N

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P |1 Strain gage- d D E 2 H b Answer: P= i N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 185 mm. The cross-sectional dimensions of the tee shape are b = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 400 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x
ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
In a laboratory test of a beam loaded by end couples, the fiber at layer -3 AB as shown are found to increase 40 x 10mm while those at CD decrease 70 x 10 mm in the 250-mm-gage length. Using E= 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. -3 Given: a 60 mm, b 120 mm, and C 80 mm. gage length a mm A 8. b mm D. c mm
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 103 mm while those at CD decrease 80 x 10 ³ mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b 130 mm, and c = 90 mm. gage length a mm b mml c mm
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are b1 = 33 mm, d1 = 110 mm, b2 = 20 mm, d2 = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10 -3 mm while those at CD decrease 80 x 10 -3 mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 50 mm, b = 140 mm, and c = 80 mm.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 50 x 10 mm while -3 those at CD decrease 60 x 10 nm in the 210 mm gage length Using E 140 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a 50 mm, b 130 mm, and c 80 mm. gage length la mm omm c mni
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 250-mm-gage length. Using E = 110 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.