A slab 0.2 m thick with thermal conductivity of45 W/mK receives heat from afurnace at 500 K both by convection andradiation. The convection coefficient has avalue of50 W/m2K. The surface temperature is 400K on this side. The heat is transferred tosurroundingsat To2 both by convection and radiation. Theconvection coefficient on this side being 60 W/m2K.Determine the surrounding temperature.

Answered: Image /qna-images/answer/174b7f8a-c307-446a-91d7-a2b5f17a3b0e.jpg

A slab 0.2 m thick with thermal conductivity of 45 W/mK receives heat from a furnace at 500 K both by convection and radiation. The convection coefficient has a value of 50 W/m2K. The surface temperature is 400

A slab 0.2 m thick with thermal conductivity of 45 W/mK receives heat from a furnace at 500 K both by convection and radiation. The convection coefficient has a value of 50 W/m2K. The surface temperature is 400

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2:A circuit board houses on its surface120 closely spaced logic chips, each dissipating 0.12 W. If theheat transfer from the back surface of the board is negligible, calculate (a) the amount of heat this circuit board (15 cm x20 cm) dissipatesduring a 10-hour period, in kWh, and (b) the heat flux on thesurface of the circuit board, in W/m2
An electrical wire with 0.4cm in diameter and 2.5m long extends across a room with 15deg C temperature. Heat is generated in the wire as a result of resistance heating, and the surface of the wire is measured to be 162degC. the voltage drop and electric current along the wire is 60V and 1.64 A, respectively. Determine the convection heat transfer coefficient for the heat transfer between the surface of the wire and the room air. Hint, electric power formula. Round your answer to 2 decimal places.
= A processing plant is convectively heating a solid half-sphere of radius of 12 cm made of pure aluminum (k 237 W/m-K) by placing it on an insulated surface as shown in Fig. 1. It is exposed to hot exhaust gas at 300°C with a convection coefficient of 180 W/m².K. Is the lumped capacitance approximation valid? Figure 1: Half-sphere
A wall receives sunlight from 7:30 am to 6:30 pm. The amount of energy it receives is 420 W/m2 and 15% is emitted as radiation into the surrounding air. The inside of the wall has a temperature of 48°C. If the wall is 7 m long and 6 m high and 30 cm thick, what is the temperature when x=20 cm?
نقطتان )2( A sphere ( k=204 W/m K) with inner diameter 4 cm and outer diameter of 8 cm. The inside temperature is 100C and the outer temperature 50 C. Calculate the rate of heat transfer
A polished metal pipe (8 cm) outside diameter and 350 K temperature at the outer surface is exposed to ambient conditions at 285 K temperature. The emissivity of the surface is 0.3 and the convection coefficient of heat transfer is 13.5 W/m2-deg. What would be the overall coefficient of heat transfer by the combined mode of convection and radiation?
The outside temperature on a particular winter's day is 0°C. Consider two identical houses, each of external surface area 200 m² and internal temperature 20°C. The walls of the first are constructed of a single layer of brick, of thermal conductivity 1 W m-1 °C-1 and thickness 20 cm. What is the heat flux Q out of this house? What is its rate of heat loss in Watts? The walls of the second house are constructed of two layers of brick, each 10 cm thick, and a layer of insulation, also 10 cm thick. The insulation is made mostly out of air, thermal conductivity 0.01 W m of heat loss from this house? How different would your answer be if you neglected the layers of brick in this calculation? -1 °C-1. what are the heat flux and the rate
A 12 in x 14 in x 350 rpm single acting oil engine has a compression pressure of 328 psi and a maximum explosion pressure of 628 psi. The connecting rod for this engine is to be made of cold drawn, C1040 steel. What should be the factor of safety of this design? What diameter is allowed using this factor of safety?
Calculate the heat transfer in kj per hour through a solid brick wall 9 cm, 3 m high and 219 mm thick, when the outer surface is at 5C and the inner surface 17C, the coefficient of thermal conductivity of the brick is 0.6 W/m-K.
A large spherical storage tank, 2 m in diameter, is buried in the earth at a location where the thermal conductivity is 1.5 W/m.°C. The tank is used for the storage of an ice mixture at 0°C, and the ambient temperature of the earth is 20°C. Calculate the heat loss from the tank.
The horizontal roof of a building has an emittance of 0.9. Air temperature is 1oC on a clear night. Sky acts as a black radiation sink at -60o If the underside of the roof is well insulated, estimate the roof temperature. Assume a convective heat transfer coefficient of 5 W/m2 K.
A processing plant is convectively heating a solid half-sphere of radius of 12 cm made of pure aluminum (k 237 W/m.K) by placing it on an insulated surface as shown in Fig. 1. It is exposed to hot exhaust gas at 300°C with a convection coefficient of 180 W/m2.K. Is the lumped capacitance approximation valid? Figure 1: Half-sphere