The temperature of a cylindrical tank containing liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located: h = 4.35 W / m2K, ∈ = 1.

The temperature of a cylindrical tank containing liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located: h = 4.35 W / m2K, ∈ = 1.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.69P: The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per...

See similar textbooks

Similar questions

What’s the correct answer for this please ?
Water with a temperature of 15 ° C approaches vertically to a cylinder with a surface temperature of 120 ° C and a diameter of 25 mm. The velocity of the water has been given as 1 m / s. What is the heat transfer rate in kW / square meter?
During daytime, the outside air temperature is measured at Ta = 35 °C. A house with an inside temperature of Tin = 20 °C is separated from the outside by a brick wall as shown in Figure 1. i Briefly discuss what will happen in terms of heat transfer process and the mode of heat transfer involved. ii. Identify the parameters that affect the rate of heat transfer in this case T. = T = 35°C 20°C Brick wall
The boiling temperature of nitrogen at atmospheric pressure at sea level (1 atm pressure) is -196 °C. Therefore, nitrogen is commonly used in low-temperature scientific studies since the temperature of liquid nitrogen in a tank open to the atmosphere will remain constant at -196 °C until it is depleted. Any heat transfer to the tank will result in the evaporation of some liquid nitrogen, which has a heat of vaporization of 198 kJ/kg and a density of 810 kg/m3 at 1 atm. Consider a 3-m-diameter spherical tank that is initially filled with liquid nitrogen at 1 atm and -196 °C. The tank is exposed to ambient air at 15° C, with a combined convection and radiation heat transfer coefficient of 35 W/m2⋅K. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the nitrogen inside. Determine the rate of evaporation (in kg/s) of the liquid nitrogen in the tank as a result of the heat transfer from the ambient air if the tank is insulated with…
In a double-glazed window, the panes of glass are separated by 1.0 cm and the space is filled with a gas with thermal conductivity 24 mW K−1 m−1. What is the rate of transfer of heat by conduction from the warm room (28 °C) to the cold exterior (−15 °C) through a window of area 1.0 m2? You may assume that one pane of glass is at the same temperature as the inside and the other as the outside. What power of heater is required to make good the loss of heat?
Heat is lost through the glass pane of a window. The thickness of the glass is 3 mm, and the window is 0.9 m by 1.8 m. The thermal conductivity of glass is 0.8 W/mK. If the temperature difference across the glass is 17 K, what is the total heat transfer through the pane of glass? Give your answer in Watts to the nearest integer.
Determine the ratio of thermal conductivity for N2 at sea level (T = 300 K, P = 1 atm) versusthe lower stratosphere (T = 230 K, P = 0.25 atm).
Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
Pls answer q3(as I am still not sure whether or not I did q2 correctly)
Q3/A sphere of 30 mm diameter has its surface maintained at 80°C while being immersed in still water at 20°C. Determine the power required to maintain the temperature.
A steel plate of thermal conductivity 50 W/mK and thickness 10 cm passes a heat flux of 30 kW/m2 by con- duction if the temperature of the hot surface is 100°C then what is the temperature of the cooler side of the plate (A) 40°C (С) 60°C (В) 50°C (D) 70°C
Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces