A wall receives sunlight from 7:30 am to 6:30 pm. The amount of energy it receives is 420 W/m2 and 15% is emitted as radiation into the surrounding air. The inside of the wall has a temperature of 48°C. If the wall is 7 m long and 6 m high and 30 cm thick, what is the temperature when x=20 cm?

A wall receives sunlight from 7:30 am to 6:30 pm. The amount of energy it receives is 420 W/m2 and 15% is emitted as radiation into the surrounding air. The inside of the wall has a temperature of 48°C. If the wall is 7 m long and 6 m high and 30 cm thick, what is the temperature when x=20 cm?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.29P: 1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that...

See similar textbooks

Related questions

Q: 2- In order to determine the effects of a force. A. magnitude of the force B. line of action. nature…

A: When a force is acting on body, it effects the body as if the body is at rest than body start moving…

Q: Find the rate of heat transfer if the cylinder in a stainless steel rod. k = 15 W/m·K (8.7…

A: Given data: ● The thermal conductivity of steel rod: k = 15 W/m•K = 8.7 Btu/h•ft•°F ● The length of…

Q: A cylindrical pressure vessel of radius r = 10.2 in is filled with a gas at a pressure of 455.0 psi…

A: Given Radius, r = 10.2 in Cap radius, R = 22 in Pressure, P = 455 psi Weight, W = 31…

Q: what are the symbols for frictional force, applied force, normal force, and gravitational force?

A: ■ The frictional force exist due to surface roughness and the relative motion between the bodies. ■…

Q: Moment of the single 100 lb force i. When the tail of the force is at its original position using M…

A: Given, We have to consider only the single 100 lb force.

Q: B- Find an expression for Cp - Cv if the equation of state is p = RT for ideal gas. na an - and Show…

Q: ᴀɪʀ ᴀᴛ ᴀ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ᴏꜰ 33°ᴄ ʜᴀꜱ ᴀ ʀᴇʟᴀᴛɪᴠᴇ ʜᴜᴍɪᴅɪᴛʏ ᴏꜰ 50 ᴘᴇʀᴄᴇɴᴛ. ᴅᴇᴛᴇʀᴍɪɴᴇ (ᴀ) ᴛʜᴇ ᴡᴇᴛ ʙᴜʟʙ…

A: Given Dry air temperature = 33o C Relative humidity = 50% To find Wet bulb temperature Dew point…

Q: You are drilling a vertical hole in an offshore oilfield NW of El Nido Palawan. At a depth of 2400m…

A: Given: Encountered a stratigraphic layer of shale at 2400m Broke out of shale formation at 2650m…

Q: The reason for the reversed carnot cycle not to be suitable for refrigeration cycles is a. Not…

Q: Oil with S.G. = 0.86 is being transported in a pipe. Calculate the pressure if a U-tube manometer…

Q: What is the control plane's principal function?

A: Introduction: In a network there are various planes have different works. Every plane or part of…

Q: Q1) A homogeneous of M kg supported at either end by a cable as shown in figure beside. If the…

Q: A reversing elbow used to deflect water flow at a rate of 14 kg/s in a horizontal pipe to make a…

Q: IS Is the resisti relative motion of two surfaces in contact Normal force оо friction O the…

Q: Determine the x-coordinate of the mass center of the aller hemi- am

Q: Determine the equivalent spring stiffness constant of the following spring in series and parallel.…

Q: What are the parts of a Vernier caliper and the function/s of each part

Q: Which of the following correctly describes the direction angles for vector F₂ in problem F2-18: 30°…

Q: A- Define the following with mathematical expression if needed: 1- Closed system, 2- Cycle, 4-…

Q: Create an isothermal process that takes a gas/thermodynamic system from a Pi, Ti, V; to a state…

Q: A- A rigid vessel of 5 m³ contain water in at a quality of 0.8 and a pressure of 2 MPa. If the…

A: Given data:- The volume of the rigid vessel V= 5 m3 and the quality of water x=0.8 and the pressure…

Q: How did you get the summation of forces in each direction?

A: We can easily find the vector form of each force and then consider the sum of all the forces acting.…

Q: 3. mi α Ti Li M L₂ T2 0 Sistem crane terdiri dari batang baja bermassa M. Tentukan rumus /persamaan…

A: given; find tension T1 and T2 ?mass m1,m2 and M

Q: A 60 lb/ft -3 ft - 12 ft- C

A: Given,

Q: * is the force resisting the relative motion of two surfaces in contact Normal force friction the…

Q: 2. A couple in Figure 2 consists of two vertical forces of 60-lb each. One force acts up through 'A'…

Q: Find the rate of heat transfer if the cylinder in a stainless steel rod. k = 15 W/m·K (8.7…

A: Givenk=15W/mKL=1mTh=200oCTc=100oCA=5cm2=5×10-4 m2

Q: Convert from decigrams to pounds 4dg->1B Transfer from Dream to Desigram dcixss->dg Convert from…

A: 1. Convert from decigram to pound 1 dg = 14535.92371 dg = 0.0002204622621847756 lbso,4 dg = 4…

Q: Two reversible cycles are in series, each process doing the same net work, Wcycle. The first cycle…

A: Given data: Higher temperature (TH)=1000°RLower temperature (TL)=400°R Need to determine the…

Q: L₁ Rigid bar ABCD is supported by two bars as shown. There is no strain in the vertical bars before…

A: Calculate the contraction in bar (2).

Q: The resultant of the two forces acting on the block is known to be a horizontal 80-N force pointing…

A: Given data: ResultantR=80 NP=50 N Need to determine the magnitude and direction of the force F.

Q: Q2) A cylindrical body of length 0.9 m and of sp.gr = 0.7 is floating in water as shown in fig.2.…

A: Write the given data. L=0.9 mSG=0.7MG=-0.03 m In this problem, the distance between meta-centre M to…

Q: Consider a two-stage cascade refrigeration cycle with a flash chamber as shown in the figure with…

A: Given: Two stage cascade refrigeration system with a flash chamber using R134a Refrigerant.…

Q: The outer surface of an oil heater at a uniform temperature of 100°C is to be filled with straight…

Q: Panous distributed forces are exerted on the beam shown, w(x) = 2.234 N/m, p(x) = 1.551 N/m, q(x) =…

Q: What is Bragg’s law? What is its use

A: intro- Bragg's law are used for defining the wavelength and lattice spacing of the crystal.

Q: Is it possible that during sensible cooling process the condition of air reaches a relative humidity…

A: Sensible collingSensible cooling is the removal of heat from the air without changing the moisture…

Q: Cylinder E weighs 150 N; angle theta is 15 degrees. Weight of cylinder F required for equilibrium?

Q: CP-5 An ideal gas with C,= 5R/2 is initially at P₁=4atm, V₁=1L. a) The volume of the gas is…

Q: (12 mins) The penstock supplies water from a reservoir to the Pelton wheel with a gross head of 516…

A: Given data:- The gross head of the Pelton wheel turbine Hg=500 m and the head loss into the friction…

Q: The weight of the body is 100 lb. Determine the rate of acceleration if a net force of 50 lb is…

Q: What is the weight of a 12 pound mass at standard gravity in Newton, dynes and lbf.

A: Given that :- Mass (m) = 12 lb To Find :- Weight (W) in Newton, dynes and lbf

Q: Given the specific volume of a gas is 0.85 m^3/ kg, compute its corresponding specific weight.

A: Given data: The specific volume of a gas: vs = 0.85 m3/kg Required: The specific weight (γgas).

Q: A- A rigid vessel of 5 m³ contain water in at a quality of 0.8 and a pressure of 2 MPa. If the…

A: Given data: ● The volume of the rigid vessel: V = 5 m3 (Note: Since the vessel is rigid, the…

Q: Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three…

A: Given: There are four balls of equal radius. So let the radius of each ball is r From the symmetry…

Q: If the resultant force is required to act along the positive u axis and have a magnitude of 14 kN,…

Q: Calculate the axial stress in a tube that is stretched by a tensile axial force of 4500 N if the…

A: Write the given data. F=4500 Ndo=25 mm=0.025 mdi=20 mm=0.020 m

Q: The 70-mm-diameter steel rod ABC, and a brass rod CD of the same diameter, are joined at point C to…

A: As per the company's guidelines when multiple sub parts are asked only first 3 have to be answered.

Q: A Carnot engine receives 120 BTU of heat form a hot reservoir at 740 °F and rejects 58 BTU of…

A: GIVEN DATA- Higher Temprature T1=740'F Heat Supplied Q1=120BTU Heat Rejected Q2=58BTU We have to…

Question

If the wall is 7 m long and 6 m high and 30 cm thick, what is the temperature when x=20 cm?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

how did you get 51.31°C?? i have tried and tried and nothing gives me that.

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per square meter will be transferred in this system if the temperature difference is 10C?
Required information Consider a person whose exposed surface area is 21 m4, emissivity is 0.5, and surface temperature is 32°C. Given: 0 = 5.67×10-8 W/m2.K4 Determine the rate of heat loss from that person by radiation in a large room having walls at a temperature of 300 K (upto 3 decimal places). You must provide an answer before moving to the next part. The rate of heat loss from the person at 300K is W.
Heat is lost through the glass pane of a window. The thickness of the glass is 3 mm, and the window is 0.9 m by 1.8 m. The thermal conductivity of glass is 0.8 W/mK. If the temperature difference across the glass is 17 K, what is the total heat transfer through the pane of glass? Give your answer in Watts to the nearest integer.
A wood stove is used to heat a single room. The stove is cylindrical in shape, with a diameter of 26 cm and a length of 52 cm, and operates at a temperature of 490°F. If the temperature of the room is 60°F, and if the emissivity is 0.844, then Calculate, the amount of radiant energy delivered to the room by the stove each second (KW) Answer
What are the equations for heat transfer from conductions, convection, and radiation?
A furnace must be built with an inner layer of refractory brick (conductivity 1.27 Kcal/h mºC). This layer must be coated with a layer of insulating brick (conductivity 0.134 Kcal/hm ºC) 22 cm thick, in turn covered with a 15 cm layer of building brick (conductivity 0.75 Kcal/ hm°C). The inner surface of the refractory wall will operate at 1150ºC and the outside at 65ºC. How many centimeters of refractory brick would be required for the insulation not to exceed 930ºC (safety limit of the material in question).
1. A 1000-W iron is left on the iron board with its base exposed to the air at 20°C. The convection heat transfer coefficient between the base surface and the surrounding air is 35 W/m². °C. If the base has an emissivity of 0.6 and a surface area of 0.02 m², determine the temperature of the base of the iron. 2. The inner and outer surfaces of a 5-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m °C are maintained at temperatures of 20°C and 5°C, respectively. Determine the rate of heat transfer through the wall, in W.
The interior surface of a 25 cm thick wall has a temperature of 27 \deg C as shown in the figure. The outer surface is exposed to a solar radiation of 150 W/m^2 and exchanges heat by radiation and convection with the surroundings and the air that are at the same temperature of 40 \deg C. The coefficient of heat transfer by convection is 8 W/m^2* K, consider both the absorptivity (\alpha ) and emissivity (\epsi equal to 0.8. Assuming transfer of 1D heat and at steady state, determine the surface temperature outside and the heat flow by conduction in the wall in three conditions different: a) If the wall is made of brick (k=0.72 W/m*K) b) If the wall is made of wood (k=0.17 W/m*K) c) If the wall is made of rigid foam (polyurethane) (k=0.026 W/m*KMake a diagram of the corresponding thermal resistance circuit and a diagram of the variation of temperatures from the interior wall to the air abroad.
Consider a person standing in a room kept at 22°C at all times. Your house It has been observed that the inner surfaces of the walls, floor and ceiling are at an average temperature of 15°C. If this person's exposed surface area is 1.4 m2 and if the average external surface temperature is 30°C, this person and the surrounding surfaces Determine the radiation and heat transfer rate between One's emissivity, the Stefan-Boltzmann constant a=5,67x10 -8 W/m 2 K 4
In a lab testing material samples to determine the thermal conductivity of the material. Now, the test specimens are 18.5 cm long by 14.4 cm wide and 0.26 cm thick. The sample is placed in a test device so that one of the large sides is maintained at 13, while the other large side is kept at -7. The heat transfer through the sample is measured to be 287 Watts. Determine the thermal conductivity. Give your answer to 2 decimal places.
How do convection and conduction work together to transfer heat?
Required information Consider a person whose exposed surface area is 21 m2, emissivity is 0.5, and surface temperature is 32°C. Given: 0 = 5.67x10-8 W/m2.K4 %3D Determine the rate of heat loss from that person by radiation in a large room having walls at a temperature of 280K (upto 3 decimal places). The rate of heat loss from the person at 280K is W.