A sinusoidal baseband signal of frequency 5kHz is transmitted using DSB-LC method using (1MHZ, 2V) carrier with u=10%. If the demodulator has input-output characteristics (V, = 3V7) and an IF filter (ideal and unity gain) is used before demodulator with center frequency at 1.002MHZ and 10kHz bandwidth. Find the output signal waveform of this demodulator, as shown: R K De- modulator DC removal LPF IF BPF fk=10kHz U = 3K2

A sinusoidal baseband signal of frequency 5kHz is transmitted using DSB-LC method using (1MHZ, 2V) carrier with u=10%. If the demodulator has input-output characteristics (V, = 3V7) and an IF filter (ideal and unity gain) is used before demodulator with center frequency at 1.002MHZ and 10kHz bandwidth. Find the output signal waveform of this demodulator, as shown: R K De- modulator DC removal LPF IF BPF fk=10kHz U = 3K2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(b) High-frequency ECG biopotentials analysis in the ST-T segment of a high-resolution ECG signal recording requires the analysis of signal components above 30 Ilz and below 800 Hz. Design a first order band pass passive filter to accommodate this specified frequency bandwidth. Sketch the circuit configuration. You may use an op- amp buffer stage in your circuit design.
Problem A For the Circuit Shown: Derive the equation for the magnitude of the gain. Include a detailed set of steps Begin with the given circuit. Each step should include an explanation (example, circuit analysis theorem, math step). O Va Provide a sketch of the Bode Plot for the magnitude of the gain. Use the two- asymptote representation in addition to other curves and information as needed. Indicate the 3db frequency, the gain in the passband, axis identifiers along with units. For the equation for magnitude of the gain, plug in frequencies 0 Hz and "infinite” Hz (this can be considered several multiples of the 3db frequency). Approximate the magnitude at these 2 frequencies and highlight the frequencies on the Bode Plot. R Vb с
Tuned Circuit Design Using a VARICAP (a) Refer to the capacitance curves for the Motorola 1N4002 The input tuning circuit of a standard analog FM radio is given below. Specify, that is design for, a voltage, capacitance, and inductance required to tune the circuit to the center frequency of KUMD-FM which operates at 103.3 MHz. Sketching and labeling a representative resonance curve is required to support your calculations. There is no single correct design answer set of values since it depends upon the voltage you initially select to tune your diode.
He (e tw) -27 27 The frequency-omplitude graph of discrete time low pass filter is given above. Based on this graph, find the time domain equivalent of a high-pass fiter in the time doman by inverse fourter transformartion.
Explain how does LCR circuit work, impedance of LCR circuit in resonance, condition for resonance in LCR circuit and also discuss quality factor in LCR circuit?
I need the answer as soon as possible
A receiver is invented by US engineer Edwin Armstrong, which it converts high frequency to low frequency, all processing takes place at lower frequencies. It offers superior sensitivity, frequency stability and selectivity. With neat block diagram and explain each blocks.
5. According to the relationship between matching filter transmission function and input determination signal in white noise background, briefly describe the principle of matching filter in white noise background ; briefly describe the reason why the matching filter is adaptive for signals with similar waveform but different amplitude and delay parameters.
Compute the eight-point DFT of the sequence x(n) using radix-2 decimation-in-time. Follow exactly the corresponding signal flow graphs and keep track of all the intermediate quantities by putting them on the diagram. x(n)=1/2.sin(pie/4.n),0<=n<=?
Discuss in detail about the narrowband noise and analyze the properties of in- phase and quadrature components of narrow band noise.
Find the normalized frequency that corresponds to a DT filter cut-off of pi/4. What normalized frequency corresponds a cut-off of 500Hz if the sampling frequency is 11,025 Hz?