A single strain gage, placed in the veritical plane on the outer surface and at an angle of 60° to the axis of the pipe, gives a reading at point A of €=250(10^-6). The pipe has an outer diameter of 1 inch and and inner diameter of 0.6 inches and is made of C86100 Bronze. 60° 8 in. 6 in. Determine the principle strains in the pipe at this point.

A single strain gage, placed in the veritical plane on the outer surface and at an angle of 60° to the axis of the pipe, gives a reading at point A of €=250(10^-6). The pipe has an outer diameter of 1 inch and and inner diameter of 0.6 inches and is made of C86100 Bronze. 60° 8 in. 6 in. Determine the principle strains in the pipe at this point.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: During a test of an airplane wing, the straingage readings from a 45° rosette (see figure) are…

A: Given data: ε0=520×10-6ε45=360×10-6ε90=280×10-6

Q: Solve it correctly please. I will rate accordingly with 4votes.

A: Given data:- Inner diameter, d= 4 inch Wall thickness, t=0.1 inch Internal pressure, P=50 ksi Axial…

Q: 4. A 45° strainmounted on thebracket. The following readings are obtained for each gauge:€4 =…

Q: Determine the largest permissible value of P for the beam and loading shown, knowing that the…

Q: A single strain gauge, placed in outer surface and at an angle of 30 gives a reading at point A of…

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

Q: Required information A cast-iron tube is used to support a compressive load of 3 kip. Given: E =…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: The vertical portion of the press shown consists of a rectangular tube of wall thickness t = 10 mm.…

Q: The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to…

Q: Full solution.

A: The diameter of steel bar, Ds =28mmThe length of steel bar, Ls=0.4m=400mmThe inside diameter of…

Q: Q5) The wooden block shown in Figure (4) will fail if the shear stress acting along the grain is…

A: In the given plane only stresses acting along X and Y direction and no shear stress (Txy =0) is…

Q: A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate…

Concept explainers

Landfills

The landfill is a site used for the disposal of waste materials. The landfill is a solid waste facility that is often known as a dumping ground. The image below shows a landfill site in Hawaii. Landfilling is the most ancient and common method used for the disposal of waste. For the landfill, a deep trench is constructed in an isolated place away from the city. The trench for landfills is designed properly after analyzing the total population and the waste generation per capita. The waste is dumped into the trench and after every layer of waste, a layer of soil is spread on the top of it.

Question

A single strain gage, placed in the veritical
plane on the outer surface and at an angle of
60° to the axis of the pipe, gives a reading at
point A of €=250(10^-6). The pipe has an
outer diameter of 1 inch and and inner
diameter of 0.6 inches and is made of C86100
Bronze.
60°
8 in.
6 in.
Determine the principle strains in the pipe at
this point.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(4) Two kids (200 N each) are balanced on a seesaw. Plane a-a (containing Point A) is just left of the pin support. Plane b-b (containing Point B) is just right of the pin support. Illustrate the combined state of stress at Point A and at Point B on the two stress cubes below. (Yes, compute values, of course.) Ans. 214 kPa 1.2m 1.2m Point A (on plane a-a): x y ^y 4 200 N A SEESAW GIVEN: Iy= 2.488 E6 mm 4 I₂0.9338 E6 mm 4 12 14 14 12 N 12 ib 33 лу 33 x 2000 Points A&B dims. in mm Point B (on plane b-b): ^y ------ NA x ----- N
Problem 7 The drill is jammed in the wall and is subjected to the torque and force shown in . Part A Part B A = -215 MPa Correct Part C ((Txy)v) ₁ = 0 MPa A X y Correct a 20 N-m Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: 125 mm Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: 400 mm Section a-a 5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N
The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. It is subjected to the couple shown where F = 2.8 kN. (Figure 1) Figure 400 mm 600 mm 50 mm 50 mm 1 of 1 Determine the maximum shear stress in region AC. Express your answer to three significant figures and include appropriate units. (TAC)max = 61.1 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 9 attempts remaining (TCB)max = MPa Determine the maximum shear stress in region CB. Express your answer to three significant figures and include appropriate units. μA Value ? Units ?
Part A Determine average normal stress. (Figure 1) Express your answer with the appropriate units. Javg = Part B μA Submit Request Answer Value σ1,02= 20 MPa IVD ΑΣΦ11 Units vec ww Determine the principal stress. Enter your answers numerically separated by a comma. ? 80 MPa 30 MPa www MPa
1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE WEIGHT OF THE WIRE, DTERMINE THE REQURIED 500 Ib DIAMATER IF THE STRESS IS NOT TO EXCEED 20 ksi AND THE TOTAL ELONGATION IS NOT TO EXCEED 0.20 in. ASSUME E = 29 x 106 psi.
with FBD please Complete solution thank you
a. Determine the maximum flexural compressive stress in the beam. Answer in MPa rounded-off to 3 decimal places. b. Determine the maximum flexural tensile stress in the beam. Answer in MPa rounded off to/3 decimal places