A single stage, single acting reciprocating compressor has a bore of 250 mm and a stroke of 550 mm. It runs at a speed of 300 rev/min. The clearance is 4% of swept volume, and the polytropic index is 1.39 throughout. The intake pressure is 97 kPa at 25°C, and the final compression pressure is 600 kPa. If the free air conditions are 101 kPa and 20°C.

A single stage, single acting reciprocating compressor has a bore of 250 mm and a stroke of 550 mm. It runs at a speed of 300 rev/min. The clearance is 4% of swept volume, and the polytropic index is 1.39 throughout. The intake pressure is 97 kPa at 25°C, and the final compression pressure is 600 kPa. If the free air conditions are 101 kPa and 20°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure gauge at a micro-hydro powerhouse shows a reading of 500KN/m?. The velocity head inside the pipe can be neglected. The 2-jet Pelton wheel is having a diameter of 0.58m. The two nozzles cause a total loss of 2% of their inlet head. At rated water flow rate, the diameter of each jet of water is 2cm. The efficiency of the turbine at the rated speed of 520 rpm is 85%. The density of water is 1000 kg/m3 and gravitation constant is 9.81m/s?. (a) Determine under rated operating condition, (i) Net head available to the turbine (ii) Velocity of water jets (iii) Water flow rate to the turbine (iv) Mechanical power output
TThe venturi of a simple carburetor has a throat diar the coefficient of flow is 0.8. The fuel orifice has a and the coefflicient of fuel flow is 0.65. The gasolin surface is 5 mm below the throat, calculate * of 20 mm and er of 1.14 mm when the nozzle (i) the air-fuel ratio for a pressure drop of 0.0. tip is ne arted (ii) the aiaeDW atio when the nozzle tip is taken into account (iii) the minimum velocity of air or critical air velocity requi red to start the fuel flow when the nozzle tip is provided. Assume the density of air and fuel as 1.20 and 750 kg/m respectively.
an air compressor of three stage compresses air from 100 kpa to 1000 kpa. calculate the intercooler pressure between the first and second stage
The Venturi of a simple carburetor has a throat diameter of 25 mm and the coefficient of air flow is 0.87. The fuel orifice has a diameter of 1.35 mm and the coefficient of the fuel flow is 0.66. The petrol surface is 6 mm below the throat. Find (a) The air-fue ratio for a pressure drops of 0.07 N/m² when the nozzle tip is neglected. (b) The air-fuel ratio when the nozzle tip is taken into account (c) the minimum velocity of air or critical air velocity required to start the fuel flow when nozzle tip is provided. Take the density of air and fuel as 1.2 and 750 kg/m³ respectively.
Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device is a single stage, single-acting air compressor. Air delivery for this device is 30 bar at a speed of 1500 rev/min. The atmospheric condition of his location is 87 kPa and 20 ˚C, with a FAD of 0.22 m2 /min. The clearance volume is 4% of the swept volume and the stoke/bore ratio is 1.3/1.Take “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K Based on pictures below 1 which formula number will be used to evaluate the mass flow rate of air? 2 which formula number will be used to evaluate the delivery volume?
0/ QI diesel engine has a clearance volume is 0.00025m and bore and stroke of 152.5mm and 200mm, respectively. A charge of air at 100kPa and 20C is taken into the cylinder and compressed adiabatically y=1.4. After combustion at constant pressure the temperature is 1090°C. The expansion which follows is adiabatic. Find a- the temperature and the pressure at the end of compression b- the temperature and pressure after expansion c- the ideal thermal efficiency of the engine (591°Č,4400kPa,227°C,188kPa,0.633)
HANDWRITTEN: Learjet 35 is a multi-role business jet and a military transport aircraft equipped with tail-mounted turbofan engines. This business jet has a cruising speed of 480 mph and cruising at an altitude of 45,000 ft. The ambient pressure and temperature is 390 R and 310 psfa, respectively. If the compressor has a pressure ratio of 18:1 and the maximum operating temperature is 2885 degrees Fahrenheit. Compute for the (a) compression ratio, (b) volume and temperature at each point, (c) Heat added and Heat rejected (d) Wnet (item c), (e) Brayton work (based on compressor and turbine work), and (f) efficiency. Note: Make sure to indicate a CORRECT P-V and T-S diagram
A single stage single acting reciprocating air compressor has 0.25 m x 1.75 m runs in 750 rpm is to deliver 0.20m³ free air per second from 101.3 kPa to 355 kPa. Calculate (a) the volume displacement (b) the volumetric efficiency (c) the isothermal work done, compression is at pV =c (d) the isothermal compressor efficiency if the the indicated power of compressor is 40kW