A double acting single stage compressor runs at 363 RPM. Compressor suction is at 23°C and 100 kPa. The discharge pressure is 948 kPa. Cylinder diameter is 300 mm, and the stroke length is 650 mm. The piston rod diameter is 125 mm. The index of compression is 1.31 and the clearance ratio is 8% on both ends of the cylinder. Calculate: A. The volumetric efficiency of the compressor at each end. B. The swept volume per revolution. C. The FAD per minute. D. The Mass flow of air per second. E. The indicated Power required. F. The Isothermal efficiency.

A double acting single stage compressor runs at 363 RPM. Compressor suction is at 23°C and 100 kPa. The discharge pressure is 948 kPa. Cylinder diameter is 300 mm, and the stroke length is 650 mm. The piston rod diameter is 125 mm. The index of compression is 1.31 and the clearance ratio is 8% on both ends of the cylinder. Calculate: A. The volumetric efficiency of the compressor at each end. B. The swept volume per revolution. C. The FAD per minute. D. The Mass flow of air per second. E. The indicated Power required. F. The Isothermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple jet carburetor is required to supply 5 kg of air and 0.5 kg of fuel per minute. The fuel specific gravity if 0.75. The air is initially at 1 bar and 300 K. Calculate the throat diameter of the choke for a flow velocity of 100 m/s. Velocity coefficient is 0.8. If the pressure drop across the fuel metering orifice is 0.80 of that of the choke. Calculate orifice diameter assuming Cdf=0.60 and γ = 1.4
Give: Otto cycle Compression ratio = 9 Intake air is at 100kpa and 20°C Maximum cylinder volume = 500 cm^3 Temperature at the end of the adiabatic compression = 800 K CP = 1.01kJ/kgk, Cv = 0.718 kJ/kg, k = 1.4, R = 287.1 J/kgk m= 0.000595 T3 = 1926
A power generator with two-cylinder, four-stroke gas engine has a bore of480 mm and a stroke of 585 mm. At 300 rev/min the torque developed is10 kNm. The generator is supplied with a mixture of gas and air in theproportion of 1 to 8 by volume. The estimated volumetric efficiency is 80% and the net calorific values of the fuel is 48.6 MJ/m3. Calculate: 1. the swept volume in m3/min, 2. the volume of mixture induced in m3/min 3. the gas flow to engine m3/min4. the energy supplied by gas5. the brake thermal efficiency
1) A singe acting, twin cylinder, ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to generate 700 kW of refrigeration at -18C evaporating temperature. At this temperature, the cooling effect per kg mass is 1160 kJ. The sp volume of vapor entering the compressor is 0.592 m³/kg. Assume 85% volumetric efficiency. Calculate the bore in mm.
A petrol engine is having, stroke length of 200 mm and clerance length (clerance gap) of 20 mm. Then the compression ratio of such engine will be a. 12 b. 11 c. 0.01 d. 10
i need the answer quickly
An engine operating on the air standard heat engine has a heat rejection at constant volume rate of 525 KJ/kg of air used. The minimum pressure and temperature are 98 Kpa and 339 K, respectively. If the bore and stroke of 75mm x 82mm, with cycle efficiency of 56% under heat addition, according to PVn = C where n = ∞ . Determine The maximum temperature and pressure The amount of air used The work for the cycle
A single-sided centrifugal compressor designed with no pre-whirl has the following dimensions and data: Total head/pressure ratio: Speed: Inlet stagnation temperature: Inlet stagnation pressure: 3.8:1 12,000 rpm 293 K 1.03 bar Slip factor: 0.9 Power input factor: Isentropic efficiency: 1.03 0.76 Mass flow rate: 20 kg/s Assume an axial entrance. Calculate the overall diameter of the impeller and the power required to drive the compressor. A. 0.693 m, 3610 kW B. 0.793 m, 3710 kW C. 0.893 m, 3810 kW D. 0.993 m, 3910 kW
QUESTION 20 A single-stage, single-acting air compressor with runs at speed 600 rpm. It has a polytropic index of 1.26. The induced volume flow rate is 7.2 cubic meters per min and the air must be delivered at a pressure of 674 kPa. The free air conditions are 101.3 kPa and 15 degrees Celsius. The clearance volume is 6% of the stroke volume and the stroke/bore ratio is 1.6/1. Calculate the delivery air. Hint answer usaully in C and no need for °C.