A single plate friction clutch with both sides of plate being effective is used to transmit power  at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find  maximum power transmitted and the corresponding axial thrust, if the maximum intensity of  pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.

Q: question= Find the idle speed of the motors alone (not clamped).?

A: For solution refer below images.

Q: In TMD of two cycle machine as depicted in Figure below, the motor has maximum speed of 2970 rpm.…

A:

Q: A belt drive is to be used for transmitting 3KW from an electric motor whose speed is 1500rpm to a…

A: The reduction of the gearbox or gear ratio is evaluated by dividing the larger gear teeth number by…

Q: Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0…

A: GivenI=80 lb-ft2N1=0  to N2=1500rpm in t=3sTstart=10 in lb=1012 lb ft=1012×32.17 lb ft=26.808 lb…

Q: A steel shaft transmits 50 Bhp at 1400 rpm. Find the torque in in-lb.

A: Given data: PB=50 hpN=1400 rpm Need to determine the torque in in.lb.

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The…

A:

Q: following figure shows a belt braking system operating on a brake drum for a lifting mechanism. It…

A:

Q: A single disc clutch with both sides of the disc effective has outside diameter of 250 mm and inside…

A: A Clutch is a mechanical device used in the transmission system. clutch could be a machine…

Q: A hydraulically operated multidisk plate clutch has an effective disk outer diameter of 6.0 in and…

A:

Q: Determine the given question with correct solution

A: Given data; P=25 KW=25×103 WN=300rpmp=85 KN/m2=0.85 N/m2d2=380 mmr2=190 mmn=2μ=0.25 Find,1.outer…

Q: A worm running at 2000rev/min is to drive a worm wheel at 200 rev/min and to transmit to it 15kW.…

A:

Q: To design a gearbox that will allow a motor to lift a 120lbf load 60ft vertically in 30 seconds…

A: A transmission is another name for a gear box. A set of gears and their case, most typically…

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: A DC brushed motor has a no-load speed of wo and a stall torque of Ts. a. What is its peak power…

A: a.Here,T(ω)=Ts-TsωoωP(ω)=T(ω).ω=ωTs-ω2ωoTsNow,dP(ω)dω=Ts-2ωωoTs=0⇒ω=ωo2At…

Q: The axial load, mean radius, coefficient of friction, number of friction pairs are used to find the…

A:

Q: A single plate friction clutch with both sides of plate being effective is used to transmit power at…

A: Given:Outer radius, r2=10 cm or 100 mminner radius, r1=8 cm or 80 mmEngine speed, N=2000 rpmMaximum…

Q: l-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of…

A:

Q: Design a flat rubber belt that needs to transmit 100kW for a system consists of two pulleys of…

A:

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given                      Power, P = 5 kW Coefficient of friction = 0.25  Constant pressure, P = 1…

Q: (b) A multiple plate clutch has more number of clutch plates. A typical clutch consist of the…

A:

Q: n'. CALCULATE the number of friction plate required.

A:

Q: Q2) A flat belt drive system is to be) designed for an application in which the input shaft speed is…

A:

Q: supported ulley 2. The diameters of pulleys 2 are 10 kg and 30 kg respectively. The belt tensions…

A:

Q: A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a…

A: Write the correction factor for 18 hr/day service. fa=1.3

Q: elect a suitable chain for transmission, as follows:

A: Given: N1=1000 rpm N2=400 rpm P=12 kW minimum center distance=800 mm  Solicitation with moderate…

Q: A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is…

A:

Q: Q5: Find the relation between the two theories of clutch design regarding transmitted torque using…

A: Two theories of clutch, 1. Uniform pressure theory 2. Uniform wear theory Load, F=1.5KN Pressure, P…

Q: T1(w)=a1-b1w                            a1=150Nm             b1=1Nm . s/rad T2(w)=a2-b2w…

A: For solution refer below content.

Q: Q. A multi disc clutch has 5 plates having four pairs Myd of active friction surfaces. If the…

A: The solution is given in next step

Q: 11. Calculate the torque:

A: To calculate Torque

Q: Determine the resulting torque of a uniform pressure frictional clutch having 4 discs in the driving…

A:

Q: Calculate the torque.

A: The applied force is F = 89 cN = 0.89 NLength of crowbar L = 0.7angle = 80 degreeTorque is defines…

Q: Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0…

A: GivenI=80 lb-ft2N=0 t o N=1500 rpm in t=3sTstarting=10 lb-in=1012 lb ft=1012×32.17  lb ft2/s2=26.808…

Q: A multiplate disc clutch consist of a branz plate to transmit 10 kw at 1000 rpm di= 90 mm do= 160 mm…

A: Given     Power, P = 10 kw                di= 90 mm              do= 160 mm Friction coefficient…

Q: The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.4;…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.