A single phase distībutor AB has a total impedance of (0-1+j0-2) ohm. At the far end B, a curent of 80 A at 0-8 p.f. lagging and at mid-point Ca curent of 100 A at 0-6 p.f lagging are tapped. If the voltage of the far end is maintained at 200 V, determine : () Supply end voltage V, (i) Phase angle between V, and V, The load power factors are w.r.t. the voltage at the far end. [) 227-22 V (ii) 2°31]

A single phase distībutor AB has a total impedance of (0-1+j0-2) ohm. At the far end B, a curent of 80 A at 0-8 p.f. lagging and at mid-point Ca curent of 100 A at 0-6 p.f lagging are tapped. If the voltage of the far end is maintained at 200 V, determine : () Supply end voltage V, (i) Phase angle between V, and V, The load power factors are w.r.t. the voltage at the far end. [) 227-22 V (ii) 2°31]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. Which section of the overload relay is typically connected to voltages that range from 120 to 600 volts? a. current-sensing section b. contact section
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
A certain regulator has a no-load output voltage of 16 V and a full-load output voltage of 15.6 V. If the full-load current is 210 mA, express the load regulation in %/mA. Your Answer:
arning Portal Courses - Reports - e-Services - Academic Departments ETC CIMS - Taher Sal In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with R = 1 KO. Assume diode as Germanium and the input frequency is F= 50HZ. Vin R D2 1- Name the given circuit. 2- Find The PIV. 3- Find Current trough load resistance. ndov4- Draw the Input and Output wave forms. O E O O A lllee
In the given circuit, a step down transformer with an RMS voltage as 110V /11-0-11 V is used with RL = 1 KO. Assume diode as Germanium and the input frequency is F= 50HZ. D, CT Vin RL D2 1- Name the given circuit. 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. all
1- spark gaps testing method is applicable for testing 2- the electrical circuit that we use to measure high voltages and is not affected by frequency change 3- We can say high voltages if exceed ------------ V (Alternating voltages) 4- Transient voltages which are caused over voltages be in two forms 5- High voltages can be generated for testing in three ways ------
a. A circuit with half-wave rectified signal has a dc voltage of 0.318Vm. The rms value of the ac component of the output signal is 0.385Vm. Calculate the percentage ripple of a half-wave rectified signal.
A chopper circuit works at a frequency of 4 kHz of a 220 V dc supply. For 180 V output voltage, find the conduction and blocking periods of a thyristor in each cycle. Select one: a. 0.209 ms, 0.234 ms b. 0.404 ms, 0.055 ms c. 0.204 ms, 0.045 ms d. 0.704 ms, 0.897 ms
Draw the circuit using only ideal diodes, resistors and voltage sources to obtain the Vo-Vi relationship whose characteristic is given below (the values shown on the characteristic are slope values).
4. A DC/DC step down converter is supplied by 96 V DC supply and produces average 24 V DC output. The switching frequency is 1 kHz, Al = 10 A, R=16 Ohm a. Draw equivalent circuit and obtain the duty cycle and the value of inductance. b. How do you reduce the voltage ripple below AV=5 V.
Sub:power electric
For a buck converter, the following specifications are given: Vin = 600 V, L = 10 mH, and R =1 Q. a) Calculate the duty cycle required to deliver 200 A de into the load. b) Derive an expression for the peak-to-peak current ripple seen by the load. c) Estimate the switching frequency necessary to limit the peak-to-peak current ripple to no more than 5 A.