A single phase 220/6 Volt, 50 Hz transformerhas a rated primary current = 0.5 A. itsmaximum efficiency is at load current = 15 Aand equal to 94% at unity p.f. Its efficiencyat rated load, 0.65 p.f. lagging is:087.8%.092.3%.090.9%.O None.

Answered: Image /qna-images/answer/c5e90c4e-fed5-428c-8b64-903031788db8.jpg

A single phase 220/6 Volt, 50 Hz transfc has a rated primary current = 0.5 A. its maximum efficiency is at load current= and equal to 94% at unity p.f. Its efficie at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. O None.

A single phase 220/6 Volt, 50 Hz transfc has a rated primary current = 0.5 A. its maximum efficiency is at load current= and equal to 94% at unity p.f. Its efficie at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. O None.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
QUESTION 2 Given is a voltage regulator with a nominal output voltage Vo=11V. When the load current varies between 0.1A and 5A, the output voltage varies between 10.8V and 11V. - Determine the load regulation in percent, write the answer without the unit.
An open loop system with unity feedbak has %OS OF 16%. What is its peak amplitude (Only give numerical value)
The average or dc value of a full-wave rectified voltage with a peak value of 75V is a. 53Vdc b. 37.5Vdc c. 47.7Vdc d. none of these
2. An RLC circuit is connected across a variable frequency, 110-volt source. When the frequency is varied, the maximum effective (rms) value of the current is 5.6 A and occurs at 45 Hz frequency. At this frequency, the voltage across the capacitor is 200.8 volts. Determine the power factor of the circuit at 60 Hz.
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
A three-phase 1MW AC-DC converter is to be connected to a 2.4kVLL/60Hz AC bus that presents a 200uH inductance per phase. What is the maximum magnitude, in Arms, that the 13th current harmonic of the converter can have, in order to comply with the IEEE 519 standard?
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 5 ms/cm and the 'volts/cm' switch is on 2 V/cm. Calculate (a) the periodic time, (b) the peak to peak voltage, (c) the maximum voltage, (d) the time taken to complete half cycle The periodic time The peak to peak voltage The maximum voltage The time taken to complete half cycle
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
4) A single-phase full-wave AC voltage controller consists of two SCRs connected in invers-parallel. The supply voltage is 220V at 50Hz. The controller is used to control heater element of 2500W in an electric oven. The trigger angle is 30o. i) Draw the circuit diagram ii) sketch compatible waveforms for the supply, load and SCR voltages. iii) calculate the rms value of the load voltage and current. iv) Determine the input power factor of the circuit. v) Calculate the average value of the SCR current.