A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D = 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MV Select one: O a. None of these O b. 252.12 MW O c. 155.45 MW O d. 170.42 MW

A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D = 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MV Select one: O a. None of these O b. 252.12 MW O c. 155.45 MW O d. 170.42 MW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the per-unit values of the elements according to the base values of 25MVA and 220kV in the system given in the figure below.
Vbase_zonel Sbase_zonel . * For the power system shown in Figure Q1b, calculate the per unit impedances of all components with given zone 1 voltage base 22kV and power base 100 MVA (for the system). = 22 kV = 100 MVA Generator: . YG₁ Zone 1 100 MVA 22 kV (0.1+ j0.5) pu 1 . E 1 T₁ YY Transformer 1: 100 MVA 25/130 kV (0.1+j0.5) pu Zone 2 L = (10+j100) S2 Figure Q1b. T₂ Zone 3 YA Transformer 2: 50 MVA 110/33 kV (0.1+j0.5) pu M₂Y Load (motor): ● 50 MVA . 33 kV (1+j0.5) pu
The subject EE463 Power Systems analysis Please show all steps , and in clear writing it is better in hand written form.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. G3: 300 MVA rating, R3 = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW
Q)The question is that how kW is converted to kVA in complex form and how kV square is 2.4 for T1,T2,T3 can you plz explain it by seeing the solution
A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 63.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.6122 c. 0.6511 d. 0.4472
Alternator A(100 kVA,3-phase, 240V,60HZ,1800 rpm) is operating with alternator B(125 kVa,3- phase,240 V,60 Hz,1800 rpm). The load of alternator A is 60kW at 90% pf lagging and the load of alternator B is 80kW at 70% lagging. Determine pf of load.
Figure below shows a power system. The rating of generators and transformers are:G1:25MVA, 6.6KV, jO.2 p.u. G2:15MVA, 6.6KV, jo.15 p.u. G3:30MVA, 13.2KV, jo.15 p.u. T1: 30MVA, 6.6A- 115Y KV, jo.1 p.u.T2: 15MVA, 6.6A- 115Y KV, jo.1 p.u. T3:single phase units each rated 10MVA, 69/ 6.9 KV, jo.1 p.u. Find te reactances in p.u, take a base of 30MVA, 6.6 KV in the circuit of G1 .=.XG1 G2} 4 A lubu T2 T1 T3 G1 G3 j120 2 j90 N
Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.01 pu and D1 = 0.8 pu on a base of 1200 MVA Area 2: R2 = 0.02 pu and D2 = 1 pu on a base of 600 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1000 MVA, what is the change in prime mover power (in MW) in Area 2 (APmech2) for a load increase of 125 MW in Area 1?
6. A generating station has the following daily load cycle : 10–12 Time (hours) 0–6 6–10 12–16 16–20 20–24 Load (MW) 20 25 30 25 35 20 Draw the load curve and find (i) maximum demand, (ii) units generated per day, (i) average load, (tv) load factor, II
The formula to calculate the load regulation is
can you please show me the sol'ncan you please show me the sol'ncan you please show me the sol'ncan you please show me the sol'ncan you please show me the sol'n