A simply supported steel beam of channel-type cross section is loaded by both the uniformly distributed load and the couple shown in Fig. 7-45. Determine the maximum tensile and compressive stresses. Also compute the shearing stress developed in the beam 20 kN/m 40 mm 40 mm 10 kN m HF 225 mm- 40 mm 200 mm 3 m Im Fig. 7-45

A simply supported steel beam of channel-type cross section is loaded by both the uniformly distributed load and the couple shown in Fig. 7-45. Determine the maximum tensile and compressive stresses. Also compute the shearing stress developed in the beam 20 kN/m 40 mm 40 mm 10 kN m HF 225 mm- 40 mm 200 mm 3 m Im Fig. 7-45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the stress in member KE for the truss loaded and supported as shown in figure (2). Note use the section method, the cross-section area of member KE is (900+15) mm? 150 Ib 6' 6' 6' 6' D G 8' 6' 250 Ib K 6' 8' Fig.2. Q2
Q2: For the cantilever beam with uniformly distributed load shown in find: a. The maximum shear stress at section 2 (within the flange) in (MPa)b. The maximum shear stress at section 2 (within the web) in (MPa)c. The maximum shear stress at section 3 (at the neutral axis) in (MPa)d. The average shear stress on the section (MPa)
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
For the beam and loading shown, consider the n-n cross section. (a) the absolute value of |M| of the bending moment in the n-n section N.m (b) determine the absolute value of the normal stress in the direction of the X axis at point A of the n-n section |σx| MPa in units, c) determine the absolute value of the maximum shear stress at Point A of the n-n section |tmaks| MPa in units. The inside of the beam is full and the cross-section measures are as shown in the figure. Supports only support vertical forces. Take P1 in the question for 220 N and P2 for 323 N. Point A is at the bottom of the beam.
Steel type is W310 X 74. P1= 40kN P2= 30kN. Find principal stress and shear stress at point '' a '' and '' b''
B1
The beam shown in Fig1.carries a concentrated load of W and a total distributed load of 8 W. Determine the maximum safe value W that will not exceed allowable stresses in tension of 60 MPa, in compression of 90 MPa, or in shear of 15 MPa. 1m W ᎦᎳ ? 15 2m 1m 20mm Fig.1 140mm 20mm 2 20mm 140mm
. The maximum tensile stress in (MPa) 5. The maximum shear stress at junction between the web and the flange (within the web) in (MPa) 6. The maximum shear stress at the neutral axis in (MPa)
Find the maximum load w applied if the allowable bending stress is 70 Mpa
For the figure shown, a truss made with members with uniform cross-sectional areas of 20 sq.mm as shown
17