A steel structural member of rectangular cross-section 50 mm wide x 200 mm deep carries a compressive load of 250 kN offset at a distance of 15 mm from its longitudinal axis. The steel has a Young's Modulus of Elasticity of 205 GN/m'. i) Calculate the maximum and minimum compressive stresses set-up in the structural member. ii) Determine the radius of curvature of the structural member.

A steel structural member of rectangular cross-section 50 mm wide x 200 mm deep carries a compressive load of 250 kN offset at a distance of 15 mm from its longitudinal axis. The steel has a Young's Modulus of Elasticity of 205 GN/m'. i) Calculate the maximum and minimum compressive stresses set-up in the structural member. ii) Determine the radius of curvature of the structural member.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam carries a concentrated load at the center which fluctuates from a value of W to 4 W. The span of the beam is 470 mm and its cross-section is circular with a diameter of 57 mm. Take ultimate stress of beam material as 683 MPa, Yield stress as 0.55 times ultimate stress and the endurance strength as 0.45 times the value of ultimate stress and take a factor of safety of 1.5. Calculate the maximum value of "W", if the variable stress induced in the beam is 109 N/mm?. Using Goodman relation calculate the value of mean stress in N/mm?. **Note: Please upload your handwritten working/solution to the link provided. Maximum Bending Moment Minimum Bending Moment Mean Bending Moment Variable Bending Moment Section Modulus, Z mm3 The value of Load "W". in N The value of Mean stress using Goodman relation ..
The following structure has a compression allowable stress of 50 MPa. In the laboratory, it was found that the allowable stress in tension is 5 MPa.
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ? P steel raid steel sF I A=0-1 Mat 50°d E = 200 GPa -Aluminum L= 250 Mm A = 1600 mm ² X = 12 x10%2 Call = 200 MPa Comp Alumivun Post. E = 73 GPa A = 2400 mM 400 mM 40o mm 2 X = 23 x 10% T = 150 MP Comp Figure 2
A 5 mm thick hollow steel rectangular tube must carry a tensile load of 200 kN. If the stress is limited to 100 MPa, which of the following sections can carry the given load. *
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
According to IS 800-1962 the permissible bending stress in steel slab plate is (b) 1420 kg/cm² (d) 1890 kg/cm² (a) 1500 kg/cm² (c) 2125 kg/cm²
STRESSES 1. A 150mm x 50mm board is glued to a triangular board. Determine the maximum shear stress of the adhesive IN BEAM material used to connect the boards. 20 KN 1 m 30 KN/m 150 mm 50 mm 1 m 1 m 15 KN/m 250 mm 15 KN/m 2 m 350 mm
Give me answer please soon
A high strength steel band-saw of 90 mm width and 0.5 mm thickness runs over a pulley of 500 mm diameter. Assuming E= 200 GPa, the maximum flexural stress developed would be
Find the maximum load w applied if the allowable bending stress is 70 Mpa
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no