A simply supported beam with overhang at the right support is shown in the Figure 2. Determine the following: a. Maximum moment b. Maximum bending stress c. If the cross-sectional area of the beam is circle with outside diameter and inside diameter of 100 mm and 80 mm respectively, determine the section modulus d. Refer to Item 2b, solve the maximum bending stress

A simply supported beam with overhang at the right support is shown in the Figure 2. Determine the following: a. Maximum moment b. Maximum bending stress c. If the cross-sectional area of the beam is circle with outside diameter and inside diameter of 100 mm and 80 mm respectively, determine the section modulus d. Refer to Item 2b, solve the maximum bending stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam carries concentrated loads at each ends, and a triangular load shown in figure. The beam is a built up shown below. Determine the maximum value of P if the allowable bending stress is1200 psi and the allowable shear stress 200 psi. W=3P P n 4 FT R1 12 FT R2 4 FT
Please answer parts A to C with legible and complete solutions.
For the beam with coordinate shown in figure. Develop the flexibility matrix. 1 L 2 C 12 B
For the beam structure shown below the data is as follows: P= 9.6-kN, L = 6-m, d= 2.4-m, b=100-mm, t-30-mm h=150-mm and h₁=130-mm. Neglect the self-weight of the beam. Based on this information answer the following question: Question 2.5: What is the maximum tensile stress in the beam? [Enter value in N and mm as appropriate] L B h
1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q-5KN/m M=4KNM F=3KN L1=3m L2=1m L3=1m 8t M F JA 10t 2t L1 L2 L3 2t 4t
A flat steel bar, 26 mm wide by 2 mm thick and 1.8 m long, is bent by couples applied at the ends so that the midpoint deflection is 27 mm. Compute the maximum stress in the bar. Use E =220 GPa. Answer must be in MPa.
Good comment will be given. Write the complete solutions and FBD legibly. Solve in 2 decimal places.
A flat steel bar, 30 mm wide by 2 mm thick and 1.3 m long, is bent by couples applied at the ends so that the midpoint deflection is 27 mm. Compute the maximum stress in the bar. Use E = 220 GPa. Answer must be in MPa.
A flat steel bar, 26 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 21 mm. Compute the maximum stress in the bar. Use E = 240 GPa. Answer must be in MPa.
Calculate the design moment strength Mu for the following section. Take f'c = 40 MPa. Sketch the strain and stress distribution diagrams for each section and try to work out your solutions using equilibrium conditions. Yield stress for N bars is 500 MPa. 75 700 60 1500 T 4N28 450
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using integration method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*10% KN.m? “4m e | Sm
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁