The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B. Determine the largest load P (kips) that can be applied at C if the stress in the steel rod is limited to 21 ksi and the vertical movement of end C must not exceed 0.12 in. Where L1 = 2.5 ft and L2 = 3.3 ft. Your final answer should have two decimal places Steel L= 4 ft A = 0.50 in? E = 29 x 10° psi B L1 L2 P

The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B. Determine the largest load P (kips) that can be applied at C if the stress in the steel rod is limited to 21 ksi and the vertical movement of end C must not exceed 0.12 in. Where L1 = 2.5 ft and L2 = 3.3 ft. Your final answer should have two decimal places Steel L= 4 ft A = 0.50 in? E = 29 x 10° psi B L1 L2 P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Computation must be complete.Answer in two decimal places.Box your final answer.
Answer in two decimal places please
#12
The beam shown is made of a nylon for which the allowable stress is 24MPa in tension and 31MPa in compression. Determine the largest couple M that can be applied to the beam. 24 mm 60 mm 30 mm 80 mm
Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram below, knowing that the maximum allowable shear stress = 107MPa and G = 40GPa. Provide your answer in kNm with precision to two decimal points. B 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 مة 0.333 0.333
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
Answer in two decimal places please
Column W200 x 71 shown in Figure 1 has the length of 4m has load of P = 150kN acting at e = 50 mm. Given the following data: E = 200 GPa, P = 150 kN and factor of safety = 2, calculate the maximum normal stress in the column. L A ========= 2 Section A-A
Situation 2: The bar AB is being supported by bars at each end. The length and the area for each bar are given. Determine the distance x to where the 100 N load must be applied if the bars must have the same stress. A. Distance x (feet) L-3 ft A= 0.2 in L=2 ft A= 0.3 in 100 N B. 8 ft
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
Consider the truss shown in (Figure 1). Suppose that F = 12 kN. gure B C D 12 m, 6 @ 2 m E F 3 m Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FCJ = Submit __ Part C μA Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Value Units Request Answer ? Units ? Determine the force in member KJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
A stat of stress is specified in Figure. By using Mohr's circle determine the normal and shearing stresses on (a) the principal planes, (b) the planes of maximum shearing stress. 20 MPa 32 MPa 10 MPa 10 MPa 32 MPa 20 MPa I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala