A simply supported beam of span 5 m and cross-section 200 mm x 600 mm is subjected to auniformly distributed load of 30 kN/m including self-weight. A plane inclined at 60° to the axis of thebeam is passing through a point P located on the central cross-section of the beam and 200 mmabove the neutral axis. Find the normal stress and shear stress on the inclined plane at point P.30 kN/m+ 200 mm200 mmNA600 mm60°2.5m-2.5 m

Step 1: L=5m B=200mm D=600 mm w = 30 kN/m θ=60 deg e=200mm

A simply supported beam of span 5 m and cross-section 200 mm x 600 mm is subjected to a uniformly distributed load of 30 kN/m including self-weight. A plane inclined at 60° to the axis of the peam is passing through a point P located on the central cross-section of the beam and 200 mm above the neutral axis. Find the normal stress and shear stress on the inclined plane at point P. N 30 kN/m 200 mm P 200 mm NA

A simply supported beam of span 5 m and cross-section 200 mm x 600 mm is subjected to a uniformly distributed load of 30 kN/m including self-weight. A plane inclined at 60° to the axis of the peam is passing through a point P located on the central cross-section of the beam and 200 mm above the neutral axis. Find the normal stress and shear stress on the inclined plane at point P. N 30 kN/m 200 mm P 200 mm NA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported prestressed concrete beam is 6 m long and 300 mm wide. Its gross depth is 600 mm. It is prestressed by horizontal cable tendons at a uniform eccentricity of 100 mm. The prestressing tensile force in the cable tendons is 1000 kN. Neglect the self weight of beam. The maximum normal compressive stress in the beam at transfer is
The beam shown has a rectangular cross section with a depth h = 240 mm. Determine the width b of the section if the material has ultimate normal stress of 100 MPa and the safety factor is F.S 1.8. 60 kN/m 70 kN-m 2 m 2 m A B C
Consider a circular beam 8 m long and 600 mm in diameter subjected to uniformly distributed load of 30 kN/m as shown in figure. 150 mm 2 m 30 kN/m 6 m B Direct shear stress developed at P will be 0.21 MPa. For analysis of point 'P' which is at AA' section, which of the following statements is/are correct? A Bending stress developed at P will be 4.24 MPa. C Maximum shear stress developed at P will be 4.26 MPa. OI D Maximum shear stress developed at P will be 2.13 MPa. 600 mm
The steel beam has the cross-sectional area shown. If w = 5.2 kip/ft, determine the absolute maximum bending stress in the beam where: L1= 6 ft; L2 = 9 ft; bf = 8.5 in; and tw = 0.3 in
A force of 3500N is acting on the orange plank which is attached to the pin as shown in the figure. a.) If the thickness of the orange plank is 75mm and the pin has a diameter of 25mm, compute the bearing stress acting between the plank and pin. b.) Compute the shearing stress acting on the pin and c.) the largest normal stress of the orange plank if it has a width of 500mm.
A cantilever beam of length 4m with a square section of side length 0.1 m is loaded vertically at the free end. The vertical displacement at the free end is 10mm. The beam is made of steel with Young's modulus of 4.0 x 1011 N/m². The maximum bending stress at the fixed end of the cantilever is
The steel beam has the cross-sectional area shown. If w = 5.4 kip/ft, determine the absolute maximum bending stress in the beam where: L1= 6 ft; L2 = 8 ft; bf = 8.1 in; and tw = 0.3 in
Two loads P acts at right angles to one another at the free end of a cantilever beam having square cross-section d x d and length 'L' on the vertical and horizontal faces. maximum bending stress in the beam will be equal to?
For given cross section with moment have 16 KN-m, kindly calculate the following ÷ a) normal stress at B b) normal stress at D
The beam below has a height of 6in and a width of 3in. What is the maximum shear stress (in psi) in the beam?
A rectangular beam 100 mm x 200 mm carries a uniformly distributed load of 5 kN/m over its simple span of 5 m. Compute for the maximum shear stress in the beam. Select the correct response: 0.94 MPa 0.38 MPa 0.66 MPa 0.56 MPa
Problem.