A simply-supported beam of length 3L is. subjected to the loading shown in the figure. P L It is given that P = 1 N,L= 1 m and Young's modulus E = 200 GPa. The cross- section is a square with dimension 100 mm. The bending stress (in Pa) at the point A located at the top surface of the beam at a distance of 1.5L from the left end is (Indicate compressive stress by a negative sign and tensile stress by a positive sign).

A simply-supported beam of length 3L is. subjected to the loading shown in the figure. P L It is given that P = 1 N,L= 1 m and Young's modulus E = 200 GPa. The cross- section is a square with dimension 100 mm. The bending stress (in Pa) at the point A located at the top surface of the beam at a distance of 1.5L from the left end is (Indicate compressive stress by a negative sign and tensile stress by a positive sign).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8 Expansion is an axial deformation. 9 True 10 False The coordinates of centroid locate the ge ometric center of the cross-section of the material.( True False Torsional stress is also known as bending stress.( True False
Problem example Example 7-5: The state of plane stress at a point with respect to the xy- axes is shown in the figure. Using Mohr's circle, determine (a) The principal stresses and principal planes and sketch the results. (b) The maximum shear stress. (c) The state of stress with respect to the x'y'-axes. 20 MPa (+) A 16 MPa 50° X 40 MPa (+) 1. Omax 3. Op 7-42
Solve the problem below and show your complete, systematic and neat solution with explanation.
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: b. Using the stress transformation equations. NOTE: support your answer with sketches and the FBD.
The figure shows a beam made from a material having an allowable tensile stress of 135 MPa and a compressive stress of 165 MPa. The couple M is applied to the beam in a plane forming an angle of 45° as shown in the figure. a) Determine the location of the centroid of the cross section b) Calculate the moments of inertia about the principal axes, I, and ly c) Determine the maximum allowable internal moment M that can be applied to the beam N M Y 140 mm 140 mm 45⁰ 140 mm 280 mm 140 mm 140 mm
Textbook: Statics and Strength of Materials Topic: Axial Shear and Bearing StressProvide step-by-step solutions.
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.19 in. In segment (2), the normal strain is measured as 1,650 pin./in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. Answers: (a) 8₂ = (b) E₁ = 41 in. (2) 93 in. lin. uin./in. P
M8
None
5 in? in. 3 in? 1 in? 500 lb. 1500 Ib. 20 in. 20 in. 20 in. E = 29 x 106 psi Member 1 2 3 a) Develop the system stiffness matrix for the three element bar shown. b) Use the applied loads and boundary condition to develop the restrained system stiffness matrix with the applied loads c) Find the deflections at each node d) Solve for the internal forces in each rod element e) Compute the strain energy in the structure. f) Verify the results that you found for c) by using classical approach, õ=(P.L)/(A.E)
THE BEAMS SHOWN IN FIGURES (a) AND (b) HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPa AND IS SUBJECTED TO A POSITIVE BENDING MOMENT Mu=140KN-m. ANSWER THE FOLLOWING.1. DRAW THE INTERNAL STRESS AND STRAIN DIAGRAM OF BEAM CONSIDERING THAT THE DEPTH OF THE STRESS BLOCK IS GREATER THAN THE THICKNESS OF THE FLANGE.