A simply supported beam is loaded by the couple M3D2000 N-m as shoWh. Thebeam has a channel-type cross section as illustrated.3 cm 30 cm3 cmT3 m10.5 cmBI12 cmmain 3 cmM-Determine the maximum tensile stress in the beam.1.60 MPaO 3.73 MPa)2.49 MPaO1.07 MPaDetermine the maximum compressive stress in the beam. *3.73 MPa1.07 MPaO2.49 MPaO160 MPaDetermine the maximum shear stress in the beam.0.0588 MPa) 0.0490 MPa0.0653 MPa() 0.0667 MPa

Answered: Image /qna-images/answer/6f07dd29-ddb5-46d3-924b-46660105b8bb.jpg

A simply supported beam is loaded by the couple M=2000 N-m as shoWH. TAE beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm T. T 3 m 2 m 10.5 cm B. 12 cm man 3 cm M Determine the maximum tensile stress in the beam. * 1.60 MPa 3.73 MPa 2.49 MPa O 1.07 MPa

A simply supported beam is loaded by the couple M=2000 N-m as shoWH. TAE beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm T. T 3 m 2 m 10.5 cm B. 12 cm man 3 cm M Determine the maximum tensile stress in the beam. * 1.60 MPa 3.73 MPa 2.49 MPa O 1.07 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3 N/m 8cm a-2 cm I m im

A: Draw the given figure

Q: If the stress in the steel is A100 = 100 ksi, what is the gross area of the steel that is required…

Q: QUESTION 3 For the beam show in figure 2, determine: (a) The reaction at the supports in term of the…

A: Given data P = 6 kn w=2kn/m

Q: The uniform beam of weight W is to be supported by the two rods, the lower ends of which were…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2 m 1m 25KN The thickness…

Q: Please show me how to solve this with the stiffness method

A: Calculate the angle:tan∅=34tan∅==36.87°Degree of freedom =5No degree of freedom at joint 1 due to…

Q: Using the node method, determine the force on the GL element and indicate whether it is in tension…

Q: If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below

A: DETERMINATION OF MAXIMUM TENSILE STRESS IN THE BEAM

Q: A structural beam subjected to sagging bending has a cross section which is an unsymmetrical I…

Q: ▾ Part A 4.5 ft- -4.5 ft- 3 ft- Determine the absolute maximum bending stress in the beam, assuming…

A: P= 16 kips

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are…

Q: 2. The following the truss figure, came from your Module 1. Page 9. 3 m H H C G 30 kN 70 kN 4 panels…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

Q: Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are…

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD2- if Beam Weighs is not know then finding of…

Q: The beam shown in the figure below has the following properties: 28-ft simple span f'c = 4000 psi,…

A: Given: l=26 ft F'c =4000 psi reinforced concrete weight =150 lb/ft3

Q: The bar ABC is fixed at A and restricted at C by two 16-mm diameter vertical steel bars, 1500 mm…

Q: 150 mm с |B 6 mm 100 mm- i The beam has simple supports and an overhang and is subjected to a point…

Q: 2. For the beam and loading shown, determine the maximum flexural stress (compression and tension)…

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A: To find deformation at point C

Q: A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm,…

A: Given data :We have to calculate the elongation of the bar

Q: Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P…

A: Given data: P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, Width of beam = 44 mm…

Q: The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional…

A: Dimension of beam:Upper plank = 25 mm×260 mmVertical plank = 220 mm×50 mmLongitudnal direction of…

Q: 14. A pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

A: Given :

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of…

Q: The material is machine steel that has a yield stress of oy = 750 MPa. P₁ = 170 MPa and P₂ = 400…

A: Given:Required:Factor of safety as per maximum distortion energy theory

Q: The steel used for the step shaft has an allowable shear stress of Tallow radius at the transition…

Q: For the beam shown below, the ratio of stiffness coefficients k41 and K43 is Assume El is constant.…

A: For the given beam,To find the ratio of stiffness coefficient

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

Q: The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and…

Q: the stresses in bars (1) and (2). the vertical deflection vp of point D on the rigid bar. the load…

Q: Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are…

Concept explainers

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur, chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.

Question

A simply supported beam is loaded by the couple M3D2000 N-m as shoWh. The
beam has a channel-type cross section as illustrated.
3 cm 30 cm
3 cm
T
3 m
10.5 cm
BI
12 cm
main 3 cm
M-
Determine the maximum tensile stress in the beam.
1.60 MPa
O 3.73 MPa
)2.49 MPa
O1.07 MPa
Determine the maximum compressive stress in the beam. *
3.73 MPa
1.07 MPa
O
2.49 MPa
O160 MPa
Determine the maximum shear stress in the beam.
0.0588 MPa
) 0.0490 MPa
0.0653 MPa
() 0.0667 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

etermine the elongation of a 0.5-in, dianeter sterl bar The elastic modulus of the steel bar is 27000 kar. 2000 Ib 10 ft
A proper cantilever ABCD is loaded as shown in figure. If it is of uniform cross-section, the collapse load of the beam will be nearly W/8 W Hagal B Mp Mp L/2 L/2 L/3 →→ D
Find the minimum principal stress for the stress case given in the figure.
Solve this
Ans (P) - 50.4KN need explanation
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
Experts Pleae help ASAP
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
Determine the stress in each member of the truss shown. Get first the value of RAv then Find the value of member AE @ Joint A
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.