A simple balance is made by a horizontal handle, a spring with a known spring constant, k= 320 N/mm and a ruler asshown in the figure. After the force P is applied on on the handle, the downward movement of the pointer on the left sideof handle is measured by the ruler as 5 = 1.3 mm. [b= 250 mm, a = 100 mm, x = 200 mm, k= 320 N/mm]CAnswer:kkabWhat is the absolute value of deformation in the spring (at B)?Answer:BAnswer:XmmWhat is the absolute value of the internal force in the spring?What would be the absolute value of the applied force on the handle?NN

a=100mm b=250mm x=200mm k=320N/mm To find deformation of spring, force in spring and value of load P

A simple balance is made by a horizontal handle, a spring with a known spring constant, k= 320 N/mm and a ruler a shown in the figure. After the force P is applied on on the handle, the downward movement of the pointer on the left of handle is measured by the ruler as 5c = 1.3 mm. [b= 250 mm, a = 100 mm, x = 200 mm, k= 320 N/mm] C Answer: B + k k a b What is the absolute value of deformation in the spring (at B)? Answer: X mm Answer: A What is the absolute value of the internal force in the spring What would be the absolute value of the applied force on the handle N N

A simple balance is made by a horizontal handle, a spring with a known spring constant, k= 320 N/mm and a ruler a shown in the figure. After the force P is applied on on the handle, the downward movement of the pointer on the left of handle is measured by the ruler as 5c = 1.3 mm. [b= 250 mm, a = 100 mm, x = 200 mm, k= 320 N/mm] C Answer: B + k k a b What is the absolute value of deformation in the spring (at B)? Answer: X mm Answer: A What is the absolute value of the internal force in the spring What would be the absolute value of the applied force on the handle N N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The turnbuckle shown in Figure has a square thread with a mean radius of 5 mm and a lead of 2 mm. If the coefficient of static friction between the screw and the turnbuckle is 0.25, determine the moment M that must be applied to draw the end screws closer together. Choices: A. 6.36 N-m B. 7.36 N-m
Determine the maximum value of b (lb/ft) if the roller at point A can only support upto 134 lb. The beam is 17 ft long while c=5.9 ft and a=1.7 ft. Round off only on the final answer expressed in 3 decimals.
gure X PDE BM_kisa_sınav.pdf Question 2) In the figure is a Russel broken traction device and a mechanical model of the leg Shows. The leg is indicated by two weights, which are connected to two cables is kept balanced in the position. The total weight of the leg and cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg, is L=100 cm and vertical distance is d=10 cm. Point C is located at three-quarters of L measured from point A (3L/4= It is 75 cm.) located is the center of gravity of the cast and leg. Horizontal of cable 2 The angle with is measured as B-40°. Accordingly,in order for b to remain balanced in the position shown Pr F8 7₁ JY W kg Wi F9 A xb My Questions | bartleby 1 A c) Find the angle of a of cable 1 with horizontal. F10 L 3L/4 2 B B F11 W a) KComposed in Ablo 1 T₁ Find the pulling force. (Write your result in N units) B b) Composed in Cable 2 T₂ Find the pulling force. (Write your result in N units) X + 72 B F12 kg W₂ d…
Please write down all the solution on paper so that i can understand. Thank youuu...
Determine the magnitude of the resultant force acting on the pin and itsdirection measured clockwise from the positive x axis. Please see the figure attached.
Plz solve in 50 mins i will give like
Problem 3: If µs = 0.35 between all surfaces (but pulleys remain frictionless), then find the smallest force P required to move the blocks. P 60 lb B 40 lb
3. Please list the given, required and the formula that had been used. Please show the diagram/illustration supporting the answer. Box the answer. Please complete the prodecure and the solution and the figure. crop it if it is long so i can see it. 0.XY= 0.68
A pump is driven from an engine crank-shaft by the mechanism as shown in Figure . The pump piston shown at F is 250 mm in diameter and the crank speed is 100 r.p.m. The dimensions of various links are as follows: OA = 150 mm ; AB mm; DE = 500 mm. Determine for the position shown: 1. The velocity of the cross-head E, 2. The rubbing velocity of the pins A and B which are 50 mm diameter. 3.The acceleration of the cross-head E. 45 A 300 600 mm ; BC = 350 mm ; CD = 150 %3D 450 100 1111 All dimensions in mm.
The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B 3 kN.m 600 mm 2 kN-m I GILM Determine the angle of twist of end A with respect to C. Take G=75 GPa. Express your answer to three significant figures and include the appropriate units. A/C= Submit μA Value Units My Answers Give Up ?
Please solve with clear step by step solutions
ENGINEERING MECHANICS UPVOTE WILL BE GIVEN. Please write the complete solutions and FBD. Rate will be given. Answer in 3 decimal places.