A L 3 B + M 2L 3 C

Q: There is a wooden beam AD, as shown in the figure below, the Flexural Rigidity of the beam section…

A: Figure is as shown

Q: Perform double integration of the bending moment equations. You will obtain deflections in this…

A: Modulus of elasticity of section, The load intensity varies from

Q: A -3 m B -3 m IC + -3 m- 60 kN m

A:

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: For the equilibrium to satisfy the centroid of the section should pass through O

Q: There is a beam as shown in the figure below, and the flexural stiffness of the beam section is…

A:

Q: An equilateral triangular prism (SG = 2/3) is floating on water as shown. A side of the equilateral…

A:

Q: -2 m -4 m- C 4 m

A:

Q: Use any method to determine the vertical deflection at Point D.

A: Using load method of analysis to find deflection at point D in the vertically direction#####

Q: The centroid of the cross-section The moment of inertia of the cross-section.

A: Centroid Centroid of a composite figure can be found out using the relation, x¯=∑x¯iAi∑Ai and…

Q: A steel beam, of lengths a= 6 m and b = 3 m and a hollow box cross section, is supported by a hinge…

A: The intensity of q starts from zero to 3.1 KN/mThe distance 'a' is 6m. The distance 'b' is 3m.

Q: For the structure in this figure , write an expression that would determine the horizontal…

A:

Q: A W = 500 N R = 150 mm 250 mm Figure Q3

A: from the figure,using equilibrium conditionmoment at the supportMA=w150 N-mmtotal strain…

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

A:

Q: There is a beam AD subjected to two concentrated forces, as shown in the figure below, the Young's…

A: To find Slope at A and deflection at B?

Q: 1.5 m B -1 m z 2 kN A

A:

Q: Consider the cantilever beam in the figure, subject to a concentrated force P = 20kip at B and a…

A:

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A: We have to locate the centroid of the area by direct integration.

Q: he beam in the figure below is subjected to a load P=2.5 kN at its end. Young's modulus is 210 GPa…

A:

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

A: Given data: d1=0.90 ind2=0.80 ind3=1.25 inL1=11 ftL2=9 ftL3=5 ftE1=15200 ksiE2=28000 ksiE3=15200…

Q: Determine the slope at B measured counterclockwise from the positive ¤ axis. Express your answer in…

A: Free Body diagram of the given problem:

Q: The 16 × 22 × 25-mm rubber blocks shown are used in a double U shear to isolate the vibration of a…

A: Downward deflection=7mm

Q: Beam AC with constant EI has a roller support at point B and slider support at point A as shown in…

A: Step 1:Step 2:Step 3:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.