The 16 × 22 × 25-mm rubber blocks shown are used in a double U shear to isolate the vibration of a machine from its supports. An applied load of P = 690 N causes the upper frame to be deflected downward by 7 mm. Determine the average shear strain in the rubber blocks. upper U frame 16 mm 7 mm 22 mm rubber block

The 16 × 22 × 25-mm rubber blocks shown are used in a double U shear to isolate the vibration of a machine from its supports. An applied load of P = 690 N causes the upper frame to be deflected downward by 7 mm. Determine the average shear strain in the rubber blocks. upper U frame 16 mm 7 mm 22 mm rubber block

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the shearing stress developed at the neutral axis of the beam with a circular cross section having a diameter of 17 mm and a shear force V = 29 kN. Assume that the shearing stress is uniformly distributed across the neutral axis. Answer must be in MPa.
= 29,000 For the structure and loading shown below, find the lateral deflection at the top. Use E ksi and I = 250 in4 for all members. Note that in frames, we neglect axial deformation, so you can calculate the deflection at either of the upper corners; the answer will be the same. t. 201 8K 10! 1. What is the deflection at the top in inches (two decimal places) ot
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied to the wide-flange beam shown in the figure
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
Reg.no : 5395 MOS-2
c6
Question 5: A hollow steel shaft (oy = 410 MPa, E = 200 GPa) as shown in Figure Q5 is subjected to a force P = 10 kN. COMPULSORY a. Determine: i) the critical stress for the shaft for buckling (e = 0) ii) the maximum normal stress for the shaft when e = 150 mm. Show that the formula/equations selecte the culations are valid. b. Determine the maximum deflection of the shaft when e = 150 mm. e 30 mm 20 mm Section a-a Figure Q5
Q\Discuss in detail the effect of the boundary condition in the Buckling of hollow shaft.
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
FINITE ELEMENT METHODS
What is the area of the tube? What is the total length of the median line? What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object?