A shunt generator supplies a 26kW load at 220V through cables of resistance, R = 112m2. If the field winding resistance, Rf =602 and the armature resistance, Ra =40m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,

A shunt generator supplies a 26kW load at 220V through cables of resistance, R = 112m2. If the field winding resistance, Rf =602 and the armature resistance, Ra =40m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Related questions

Q: (Draw the Circuit Diagram) A self-excited shunt generator has a field resistance of 60 ohms. When…

A: Given a self- excited shunt generator with Field resistance(Rf)= 60 Ω Terminal voltage(Vt)=120 v…

Q: An 8-pole d.c. shunt generator with 778 wave - connected armature conductors and running at 500…

Q: A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage…

A: In this question We need to choose the correct option What is maximum power delivered to the load.…

Q: 9. How does the concept of magnetic saturation impact the performance of transformers and inductors?

A: Saturation in a transformer is caused by an increase in the magnetic field strength, either due to a…

Question

A shunt generator supplies a 26kW load at
220V through cables of resistance, R =
112m2. If the field winding resistance, Rf
=602 and the armature resistance, Ra
=40m2.
Determine the following below:
The terminal voltage is,
The e.m.f. generated in the armature is,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
I need the complete solution.
current and on-time? 2. A 60V chopper drives a resistive load of 12fL The chopper frequency is set to 1 kHz. Calculate the values of average and rms load currents and load power for a turn-on time of (a) 0.2ms, (b) 0.6ms.
Q9. What is the basic principle that a cage winding can be represented by a three-phase winding? Give your explanation.
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find : the magnetizing reactance the rms values of the ( magneto – motive force , exciting and armature currents , magnetic fluxflu the inductance Draw the phasor diagram of the circuit
32. An alternator requires an alternating current of 2.1 A to produce on short circuit its full-load current of 50 A. The same on open-circuit an emf of 320 V. The armature resistance is 1Ohms . Find the full-load percentage regulation with a lagging p.f. of 0.6 when terminal p.d. on load is 2000 V. A. 7.2% B. 28.8% C. 3.6% D. 14.4%
Which of the following sensors has a permanent magnet inside? Hall effect sensor thru-beam optical sensor piezo-electric sensor LVDT capacitive proximity sensor |o|0|0|6
A dc series generator is sipplying a current of 10A to a load trhrough a feeder of total resistance 1.5 ohms. The generated voltage is 550V. The armature and series field resistance are respectively 0.5 and 0.6 ohm respectively. Determine the voltage at the terminal of the generator and at the feeder.
A DC series generator is supplying a current of 5A to a series lighting system through a feeder ofto total resistance, 1.0 ohm. The terminal voltage is 2500 V. The armature and series fieldresistances are respectively 18 and 15 ohms respectively. A 30-ohm diverter resistance isshunted across the series field. Determine the power developed in the armature of thegenerator?
Suppose we have an ac current flowing through a coil wound on an iron core. Name two mechanisms by which energy is converted to heat in the core material. For each, how is the core material selected to minimize the power loss? How does each power loss depend on the frequency of the ac current?