A shaft is transmitting 2 HP at 100 rpm, n mum shear stress in shaft is 50 MPa. Nov shear stress remains the same, how much HF be transmitted at 200 rpm?

Q: A torsion dynamometer is fitted on turbine shaft to measure the angle of twist. The shaft twist 1.6°…

A: A torsion dynamometer is installed on the turbine shaft to measure the angle of twist, as we know.At…

Q: Find the force applied Work done=554.44 J Displacement=50 m

A:

Q: A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

A: Find the outside and inside diameter .

Q: problem: In the tollowing Figures, Find the force torque at the given paints. 200 N Loo N 200 N EMA…

A:

Q: mechanical engineering (Machine design) (1)Find the torque and power that a shaft with a diameter of…

A:

Q: Example (1-6): A pumping plant forces water through a 600 mm diameter main, the friction head being…

A: Given: The diameter of old pipe is d1=600 mm . The friction head in old pipe is hf1=27 m. The…

Q: Find displacement Work done=1111 J Force 111 N

A: Given: Work done , W  = 1111 J Force, F = 111 N   To find : displacement (S)

Q: Find displacement Work done=1111 J Force=111 N

A: Given data: F=111 NW=1111 J Need to determine the displacement.

Q: A rotating hollow shaft is to transmit 30kw at 300rpm, the maximum torque being 20% greater than the…

A:

Q: J:41) A motor delivering 3000 kW at 20 Hz to a partially hollow steel shaft (GSt=80 GPa) connected…

A: Write the expression for the torque that is transmitted to the steel shaft by the motor. Understand…

Q: Plz give proper Answer other wise don't attempt. A shaft of 30 kW 710 r.p.m motor is 40 mm in…

A: To find: The stress due to bending if the armature weighing 10000 N concentrated at the centre…

Q: 0. A shaft has a number of a collars integral with it. The external diameter of (uniform) and the…

A: Given data as per question  External diameter of the collar=400 mm The inner diameter of the collar…

Q: Example 19.19. A torsion dynamometer is fitted to a propeller shaft of a marine engine. It is found…

A:

Q: Eng. to select material for turbine disk based on its density, min strength 667 MPa., poisson ra. Ho…

A:

Q: 100 KN 20 KN/m 10 m need NF, SF and BM diagram ? detailed answer in a basic way

A: It is required draw NF,SF AND BM Diagram

Q: A solid steel shaft has to transmit 75Kw power at 200 pm. Taking allowable shear stress 70Mpo. Find…

A:

Q: Define I) torque II) torsional loads b)A solid circular shaft is to transmit 80kw power at…

A: Torque is defined as moment of force acting about an axis which is cabable of producing angular…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

A:

Q: Find displacement Work done=1111 J Force 111 N

A: Given data Work done (W)=1111 J Force (F)=111N

Q: Find displacement Work done=1111 J Force=111 N

A: The displacement is s = 10.009 m.

Q: (14) A 40mm steel shaft rotates @ 600rpm & handles 10kW delivered from a pulley located 300mm from…

A: Given data, Diameter of the shaft, d = 40 mm RPM of the shaft rotation, N = 600 rpm Power…

Q: Find the force applied Work done=554.44 J Displacement=50 m

A: Given:  Work done, W = 554.44 J Displacement, S = 50 m To find : Force applied (F)

Q: Find displacement Work done=1111 J Force 111 N

A: Given data : Force F=111 N Work done W=1111 J   Required : Displacement

Q: The principal stresses of the state of stress.

A: Given:- Principle stress question with solution, To find:- To clear the doubt how -53.13, 26.6, and…

Q: A drive shaft is made of solid steel. It is desired to transmit 2.5 hp at 150 rpm. The allowable…

A:

Q: In a) why you wrote ( m + 5m) , where that 5m came? You have m1 = m and m3 = 4m in the problem. So…

A: Given: The mass of the block: →m1=m And mass of the disc: →m3=4m this mass is the complete mass of…

Q: Find force value Work done=1001 J Displacement=50 m

A: Given data : Displacement=d Work done=W   To find : Force

Q: A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter…

A: The length of the shaft,(L)=1103 mm. The outside diameter of the shaft,(do)=73 mm. The inside…

Q: A hallow steel shaft transmit 600km at 500 rpm.the minimum

A: Given Power = 600 kW N = 500 rpm To find Diameter of the shaft Assuming Maximum torque is 20% higher…

Q: For the solid shaft, 1 inch in diameter, subjected to bending and torsion, find the principal…

A:

Q: A shaft that transmits 300kW at 2500revs/min consists of a tube 100mm outside diameter and inside…

A:

Q: Find displacement Work done=1111 J Force=111 N

A:

Q: is Q- The required diameter for a solid shaft 700 mm to transmit 200kW at 135rpm, with the working…

A: D=Solid shaft diameter =100mmP=Power =200kWN=Roration =135rpm

Q: Find displacement Work done=1111 J Force=111 N

A:

Q: A solid circular shaft to transmit,80kw power at 200rpm.calculate the shaft diameter and strain…

A:

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.