A shaft ABC of 500 mm length and 40 mm external diameter is bored for a part of its length AB, to a 20 mm diameter and for the remaining length BC, to a 30 mm diameter bore. If the shear stress is not to exceed 80 N/mm², find the maximum power, the shaft can transmit at a speed of 200 rpm. [The shear modulus is 80 GPa]. If the angle of twist in the length of 20 mm diameter bore is equal to that in the length of 30 mm diameter bore, find the lengths of the shaft that has been bored to 20 mm and 30 mm diameter. Also determine the total angle of twist.

A shaft ABC of 500 mm length and 40 mm external diameter is bored for a part of its length AB, to a 20 mm diameter and for the remaining length BC, to a 30 mm diameter bore. If the shear stress is not to exceed 80 N/mm², find the maximum power, the shaft can transmit at a speed of 200 rpm. [The shear modulus is 80 GPa]. If the angle of twist in the length of 20 mm diameter bore is equal to that in the length of 30 mm diameter bore, find the lengths of the shaft that has been bored to 20 mm and 30 mm diameter. Also determine the total angle of twist.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum torque of the tube shown if the allowable shearing stress is 58 Mpa. Given: t = 2.79 mm and a = 43 mm. Answer must be in kN-m. a 32°C Lig P3 43. KA EDCA ESC F7 FB E RU H. M.
EXAMPLE 2.8 Draw the SFD and BMD for the beam shown below. 1000 N/m 3m 3m Solution; Calculate the support reactions. 5000N 3m 40000Nm | 3m 3m [Ans: V₁-8000 N (†), V₁-9000 N (1)] 4000N/m
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
I. N • O P M E;Y7 Z H.W. for fatigue stresses... Q1) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length (L), if the stress at the fillet equal to the half stress at the center. de6.25 62.5 -O- 50 -375 375 Fillet Fillet All Dimensions in mm Center Fig(1) Q.) In Fig.(2), the shaft is subjected to reversed loads, F = 7 2700 N and P = F 1350 N, where these two loads vary at the same time. Find the required length (L), if the stress at the fillet equal to the stress at the center. F 2700 N P.1350 N P.1350 N 50 62.5 1500 - - Fillet Center Fillet Al Dimensions in mm Fig(2) Q.) In Fig.(3), the shaft is subjected to reversed loads, F = F 2700 N and P = F 1350 N, where these two loads vary at the same time. Find the diameter (d), if the stress at the fillet equal to the stress at the center. F- 2700 N * 10 P.+1350 N P-1350 N d. 1.6 d 500- - 1500 - 500 Fillet Center Fillet All Dimensions in mm Fig(3) Q.) In the Fig.(4) shown below, a machine member is…
Completely solve (a) and (b). Box the final answers!
M9
Urgent
Name: Class: ......... Assignment No. 3 Q4- A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in Figure. The weight of the gate is negligible, and the hinge at O is frictionless. (a) Determine the water depth, h, if the resultant hydrostatic force of the water acts 2.5 ft above the bottom of the gate, i.e., it is collinear with the applied force F. (b) For the depth of part (a), determine the magnitude of the resultant hydrostatic force. (c) Determine the force that the hinge puts on the gate under the above conditions. Water Hinge O Gate 6 ft 2.5ft Name: Class: Assignment No. 3
Determine the displacement at pulley B. The A992 steel shaft has a diameter of 30 mm.
Problem 2: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: Flow rate Inlet diameter Outlet diameter Head Width at the inlet Width at the outlet Leakage Mechanical loss Blade angle at the outlet The water density Atmospheric pressure |Q=72 L/s DI = 90 mm D2 = 280 mm H= 25m bl -20 mm b2 = 18 mm q =2 L/s Pm = 1.41 kW B2 = 35 p = 998 kg/m³ 101 kPa
Torsion. A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20 mm diameter and for the remaining length L2 to a 30 mm diameter drill hole. If the allowable shear stress is 85 MPa, find the maximum power that the shaft can transmit at a speed of 235 rev/min. If the angle of twist in the length of 20 mm diameter drill hole is equal to that in the 30mm diameter drill hole, find the length of the shaft that has been drilled to 20 mm and 30 mm diameter.