A seismic portal frame is shown in the figure below. The structure is used as an essential facility and special moment resisting concrete frame. It is built under seismic zone 4, with a fault having a potential to produce 7.2 Maximum Magnitude Moment with a Soil Profile Type C. The distance from the Seismic Source is 7.6 km. Perform PORTAL METHOD of Analysis if W1 = 3000 kN and W2 = 2000 kN.

Q: Thermocouples are devices used to measure temperature of a given sample or the surrounding medium.…

A:

Q: A 10 bit DIA converter given a maximum output of 1023V. The resolution is

A:

Q: d) Find the time constant associated with this transient analysis. e) Find the time it takes for…

A: Given Data:Find:d. Time Constant Associated with Transient Analysise. Find the time it takes for the…

Q: An inert gas held in a plunger undergoes three stages: Stage 1-2: the gas is compressed without any…

A:

Q: The composite wall of an oven consists of three materials, two of which are of known thermal…

A:

Q: Consider a cruise control system shown in Figure 1. Where f is the engine force, v is the velocity,…

A: Given the figure f= the engine force, v= the velocity,fb = the friction force, and fb  =…

Q: Question: Consider the following thermal system. The input is T in, and the output is the…

A: Given : To find : State space model

Q: A stepper motor serves as the drive unit for the linear joint of an industrial robot. The joint 24…

A: INTRODUCTION : Stepper motor converts electrical energy into mechanical energy by using electrical…

Q: Q4) Two J type thermocouples have been used to measure a temperature difference between a room and…

A: Here is the solution with the given information, the formula used, and the calculations: Given:…

Q: 2. A square is acted upon by the forces of 4, 6, 8, and 12N respectively along the four sides as…

A:

Q: c.) The black and red curves show data obtained for two different materials. Which material would…

A: Given question is related to machine design.

Q: What is the mass, in grams, of the object below? (Symmetrical | Unit: Millimeters | Physical…

A:

Q: As the control engineer on a project you are given the following information: a) The free body…

A: Given : To find : Analyze the system and to confirm if the graph is correct

Q: Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace…

A:

Q: The performance of an element can be written as p = fi(F).f:(G)fs(M). F, G and M in the performance…

A: Following is the answer to the above question

Q: conductivity

A:

Q: A metal rod, made from metal 1, with a length of 28.0 cm expands by 6.80x10 2 cm when its…

A: Solution:

Q: 6. A ball is thrown straight up in the air at time t = 0. Its height y(t) is given by 1 291² y(t) =…

A: It is asked to find the following based on the above equation

Q: Q11 As a design engineer you were ask to identify material(s) for cooking pot handle (Figure Q11).…

A: Given question: We have to identify materials for cooking pot handles.The following are its…

Q: For an infrared digital thermometer application to scan humans for fever: (a) what range of…

A: Infrared thermometers are one of the foremost prevalent sorts of thermometers as they assist you…

Q: Determine the total moment at A. SIGN CONVENTION: + ÇCW CW 25 N 65 N A B 15 N 1.5 m 2 m 1 m

A: Free body diagram  Fwom above free body diagram , we can see that there is no force in…

Q: In an specific mesh, one node is attached to 4 elements, and one another node is attached to 3…

A: Mesh is incompatible.

Q: 03/ Find the effective time constant for G(S) Y(s) 16 G(s) X(s) 1.5s2 + 2.4s +6

A: Given, Transfer functionG(s)= 16/(1.5s^2+2.4s+6) Required: Effective time constant.

Q: how convergence study can be carried out for the problem. (Note: no detailed drawing of mesh is…

A: Finite Element Analysis (FEA):Finite Element Analysis (FEA) is a key component of contemporary…

Q: Example 6: Calculate the response of Single Degree of Freedom System for the given step force by…

A:

Q: Collar A is free to slide with negligible friction on the circular guide mounted in a vertical…

A:

Q: i. Number of users that could be served per a cell,

A:

Q: 19 Find an expression for isothermal bulk modulus of elasticity for a gas which obeys Van der Waals…

A:

Q: eveloped by the high-pressure turbine (HPT) is used to 2. The low pressure turbine (LPT) provides…

A:

Q: We performed the experiment to measure CALCULATE THE FOLLOWING: MATERIAL 1 - BRASS the thermal…

A: Material 1 Brassd = 25mm, 0.025mQuantity calculatedPower ( θ') W  = 14.6WArea of cross section A =…

Q: You are charged with specifying a cooling system for a house. The solar and internal gains have been…

A:

Q: As we explained in earlier chapters, the drag force acting on a car is determined experimentally by…

A:

Q: 1. A cross-flow heat exchanger is used to transfer heat from a stream of saturated water at 100 °C…

A:

Q: Based on the pic attached, If component B of #6 is changed to 3 parallel components and each has the…

A: Rs= 0.9796766

Q: A composite wall is made up of 10 cm of common brick against 15cm of concrete with 1.5 cm of plaster…

A:

Q: ism to push a box, as shown below

A: Motor specification'   Torque  - τ = 85Nm r= 25m   (b) we know that  τ = F*r = Fr sin θ  = Fr F = τ…

Q: 3. Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace…

A:

Q: Ques.15Frames describing the base of robot and object are given relative to the universe frame. Find…

A: Given data, UTR=0-100100000140001UTobj=100100-1401000001 We know that,…

Q: A car with a mass of 1503 kg, a spring constant of 307027 N/m of suspension springs, a damping…

A:

Q: The reference mode of the load factor of a Nuclear Power Plant is presented in Figure 2. Nuclear…

A: Nuclear plant load factor formula- Plant load factor is the ratio of energy produced by a generated…

Q: 1)To design a Gold chain a goldsmith has taken 2 gram of gold (22 K) wire with 4 mm diameter.…

A: As per company policy, we are restricted to solve only first three sub-part of one question at a…

Q: Can you solve this problem as soon as possible

A:

Q: 3. sin' xcos' xdx

A: to determine- value of the integration.

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.