A seated musician plays a C4 note at 262 Hz. How long does it take for 196 air pressure maxima to pass a stationary listener?

Q: Which of the following choice(s) represent a possible correct physical relationship between E and B?…

A: Option (B) is correct answer

Q: e: sketh tha output veltage for tH folloolng circut aka

A: Disclaimer:  Since you have asked multiple questions, we will solve the first question for you. If…

Q: The function of the moderator in a nuclear reactor is to Stop chain reaction Reduce the speedof…

A:

Q: b) A circuit consists of an inductive coil (L=0.1 H, R = 10 N) in series with a variable resistor (0…

A: In this question,  Draw the current locus if supply voltage 230V, 50Hz. Inductor coil L= 0.1H, R= 10…

Q: 3.13 A second order control system has 100 M(j@) = 100 – m? + 10/2j@ Its Mp (Peak magnitude ) is

A: we need to find out Mp.

Q: Identify which measurement this oscilloscope time difference reading is useful for. Ociloscope-XSC1…

A: Given, T1= 250us T2= 1.261ms T2-T1= 1.011ms Scale: On x-axis: 200us/Div On y-axis: 100V/Div

Q: QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function…

A:

Q: A 60 Hz sinusoidal voltage with an RMS value of 440 V is applied to a TRIAC voltage regulator. The…

A: it is asked to find the output DC voltage of given TRIAC voltage regulator

Q: draw a handdrawn clear picture of 34 conductors,17 slots ,4 poles wave winding .a computarized…

A: Given No. of conductor (Z) = 34 No. of poles (P) = 4 Now Average pitch Ya = [Z +_ 2]/2 = [34 + 2]/4…

Q: Identify which measurement this osilloscope time difference reading is useful for. Ocilloscope-XSC1…

A:

Q: In a frequency modulating system, the frequency deviation constant k = 1 kHz/V. A sinusoidal…

A:

Q: the machine is generating 355 V at 60 H The e.m.f generated by a synchronous generator at a…

A: Given,  The emg generated by synchronous generator at 60 Hz and field current of 3 A is 355 volts.…

Q: Regarding behavior of inductors and capacitors in circuits, select the correct statement - a)…

A: Pure inductor circuit:  Circuit contains only inductor not containing any other elements like…

Q: Zy a o ZA Zy Zy The circuit shown is excited by a balance three phase source with a line voltage of…

A: Z∆ = 3 XZYZ∆2 =12+13 jOR21.63∠56.30  Z∆ combined = 19.2-∠-51.34 x 21.63∠56.3012-j15+12+18j∴ Z∆1 x…

Q: EX 3 - 12V Determine Vo Si Y Green ovo 2.2 K

A: Diode which have less cut in voltage will be on first then we will find out output voltage.

Q: From step1, how did you get that 50+(80*j60/80+j60) = 78.8+j38.4? also in step 2, how did you get…

A:

Q: Calculate values of asked physical quantities of the circuit in the figure. C₁ = 3.0 F C₂ = 4.0 F…

A:

Q: QUESTION 3 An inductor, a capacitor, and a resistor are connected in series with a function…

A:

Q: The advantage of ..is that it protects the entire machine from dust and dirt. It also provides . .…

A: 1. The advantage of Yoke is that it protects the entire machine from dust and dirt. It also provides…

Q: A 60 Hz sinusoidal voltage with an RMS value of 240 V is applied to a TRIAC voltage regulator. The…

A: Given, TRIAC voltage regulator having RMS value of input signal, Vrms = 240V  Frequency, f = 60Hz…

Q: For the resistor shown above what best describes its behavior at 1 MHz? O It responds primarily as a…

A: For normal frequencies the components such as resistors,capacitor and inductor work normally but at…

Q: Calculate the divergence of 6=()105yza̟ + 5x°za¸ + (2² – sx')«]at P(- 2,3,5). | 10xy Answer

A:

Q: A stationary closed Lissajous pattern on an oscilloscope has 3 horizontal agencies for a horizontal…

A: Given- Horizontal tangencies = 3, Vertical tangencies = 2, Frequency of Horizontal input = 3 kHz,…

Q: What is the frequency of the input signal if the measured capacitive reactance is equal to 28 Q.…

A:

Q: in V1 R2 100k SINE(0 10 100) R1 100k D1 ܢ D V2 out -K D D2 V3 0 DC offset(V) 0 Amplitude[V]: 10…

A: given

Q: Below are two voltage patterns measured from an oscilloscope. The voltage stage of the CHI probe is…

A:

Q: What is the maximum recommended limit of RMS voltage (in percent) for continuous operation of shunt…

A:

Q: 3) Find the tronsfer function for the block diagram i followig

A: for the given block diagram we have to find  the transfer function

Q: In a synchronous generator, choose what happens to number of poles if the value of frequency is…

A: The relation between the number of poles and frequency for a synchronous generator is related as:…

Q: Figure B1 shows a 3 phase half wave rectifier. If the firing angle, a is to set at z/6, analyze the…

A: A circuit of three phase half wave controlled rectifier is shown in the question. We need to analyze…

Q: Solve for the value of the capacitance (in nF unit) if R2-1017 ohms and Xc-2316 ohms. Round your…

A: Given data, Resistance R=1017 Ω. Capacitive reactance Xc=2316 Ω,

Q: Firing angle-5o Degree 1:2 O Vo -200/200v For the circuit shown Vo rms = 5 Ohm 50 Hs O 132.6V O21.5V…

A: This is center tap full wave rectifier.  Find the rms value of output?

Q: How will we know if the capacitor is already fully charged?

A: Capacitor is a passive device which is used to store a form of energy between its plates.

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.