A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radi, r, 0.0440 m and r, = 0.120 m, respectively. (a) If a downward force of F, 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d, = 0.208 m, through what distance d, would the other end move? m

A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radi, r, 0.0440 m and r, = 0.120 m, respectively. (a) If a downward force of F, 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d, = 0.208 m, through what distance d, would the other end move? m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the free body diagram for this problem: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom.
A boom with an angle of theta, supports a 1000 lbs load as shown in the figure. Assume that the force exerted by the boom is 3 times the force exerted by the cable that holds it in place, what is the force exerted by Cable A?
A load weighing P kN as with AB, AC and AD cables such as are carried. Points A and B are x-axis, C and D points are on the y-z plane. Specific to your name in the data table AB, AC and AD cable using ratings Calculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 %3D %3D %3D L4 (m) = 18 L5 (m) = 16 L6 (m) = 5 %3D %3D %3D
The oblique pipe in the figure is desired to be compressed. Force F is applied perpendicularly to the pipe wrench. Calculate the difference that will occur if the same key and the same force are applied between AB?
Please answer this within 30 mins! I will upvote !
The basic elements of a hydraulic press are shown in the figure below. The plunger has an area of 1 in.², and a force, F₁, can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to 1. If the large piston has an area of 190 in.², what load, F2, can be raised by a force of 30 lb applied to the lever? Neglect the hydrostatic pressure variation. F₂ F₂= lb Hydraulic fluid Plunger F₁
mb: L d- ms A horizontal L=1.2 m long mb=12 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 31° angle with horizontal. A 18 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of vertical hinge force.
Please I want you to solve the question below in the same way that I provided in another. picture I want to you to include F_R. also the coordinator x_R and YR. and x_C and y_C. also I want to know the h_C. The gate in the figure below is 5 ft wide, is hinged at point B, and rests against a smooth wall at point A. (1) Compute the force on the gate due to water pressure (Must include the magnitude and the center of pressure) (2) Compute the horizontal force exerted by the wall at point A. (3) Compute the reaction force at the hinge B (Must include the magnitude and direction
A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the following (a) the lengths LBE and LAB, in m (b) the angles a and p, in degrees Draw the complete FBD of (c)members AB, FG, EBH and GHI Calculate the forces, in Newtons, for the following (d) member FG (e) pin H (f) hydraulic cylinder AB Parameter P = 724 N 8= 34.5° Note: Figures CDFE and EFGH are parallelograms. E 100 175 bis is not y 400 LBE ou op os dadog on funt an 150, B a This is not property so do not in any way are your an 150 D E 175 B 200-- Dimensions in millimeters G PH P 150 This is not your property so do not use it in any way as if it were your
A 50 kg pole extends up a wall, making a 60° angle with the wall. The pole is supported by acable attached 3/4 of the way along the pole. This support cable is perpendicular to the wall.A 10 kg sign hangs from the end of the pole. The pole’s center of mass is 1/3 of the way fromthe wall to the end of the pole. (a) What is the tension in the cable?(b) What are the x and y components of the force the wall exerts on the pole?You must include an extended free body diagram showing all forces acting on the pole. Labelthe location on the pole you will use a reference for measuring distances (the “axis of rotation”) at the point where the pole touches the wall. Thank you!
The first figure gives spring force Fx versus position x for the spring-block arrangement of the second figure. The scale is set by Fs = 190 N. We release the block at x = 13.0 cm. How much work does the spring do on the block when the block moves from x; = +9.0 cm to (a) x = +5.0 cm, (b) x = -5.0 cm, (c) x = -9.0 cm, and (d) x = -11.0 cm? -x (cm) -2 -1 -F, X* = 0 Block attached to spring F = 0 (a) x positive F, negative F (b) x negative F, positive (c)
do all