A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r = 0.0440 m and r, = 0.300 m, respectively. A2 (a) If a downward force of F, = 12.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d, = 0.240 m, through what distance d, would the other end move?

A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r = 0.0440 m and r, = 0.300 m, respectively. A2 (a) If a downward force of F, = 12.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d, = 0.240 m, through what distance d, would the other end move?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The vertical face of a dam across a river has the shape of a parabola 20 m across the top and 10 m deep at the centre. Set up an integral representing the force that the river exerts on the dam if the water level is 6 m above the lowest point of the dam. There is no need to find the value of the force, only the set up of the integral is required, however, all the details are expected.
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, 1 = 0.0480 m and r2 = 0.300 m, respectively. (a) If a downward force of F1 = 16.0 N is applied to the end with the smaller radius, how much force F2 would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) ]N (b) If the smaller piston is pushed down a distance d, = 0.176 m, through what distance d, would the other end move? m
Two circular platforms are attached to a fluid reservoir. On one platform rests the entire cast of Glee frozen in carbonite. A force of 7.0 N is applied downward to the empty platform with radius 8.0 m. The other platform applies a force of 7.2 N to the carbonite-frozen pop-idols. What is the radius of the platform holding the Glee cast?
Water (density = 1 × 103 kg/m3) flows at 15 m/s through a pipe with radius 0.04 m. This same pipe goes up to the second floor of the building, 3 m higher, and the pressure remains unchanged. What is the radius of the pipe on the second floor? Group of answer choices
Help
The piston of the hydraulic cylinder gives pin A a the instant when 0 = 54°, determiner, 7, 9, and 6.1" Answers: r = = ö = -1.2343 i -1.6988 2.7039 10.623 ft/sec constant velocity v = 2.1 ft/sec in the direction shown for an interval of its motion. For where r = OA. ft/sec² rad/sec rad/sec²
Al Messenger Scribd google b My Questions | bart.. Clear selection The ratio of area of cross section of the two pistons in a hydraulic machine is 1:15. Find the force that should be applied on the narrower piston to overcome a force of 120 N on the bigger piston. 20 N 8 N 150 N O 10 N Dtatic field is 250 O O O
When a block (? = 6.00 ? 102 ??/?3 ) is placed inside a container full of water, it floats partially and displaces 1.25 kg of water. (a) what is the volume of the block? (b) what is the bouyant force?
A swimming pool has a length of 10 m and width of 5m. When the pool is filled to a depth of 1 meters with water, what is the force( in N) exerted by the water on each end? Aend Agide Final answer should have O decimal places. Do NOT include the unit in the final answer
Please help me ?
In a hydraulic lift system employing Pascal's law, what is the force required to lift up the larger piston? The force given at the smaller piston is 13.2 N and the ratio of A/a is 68.75. Present your answer in kN with accuracy one decimal place.
Please Asap