A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0440 m and r, = 0.300 m, respectively. A2 (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) N (b) If the smaller piston is pushed down a distance d, = 0.240 m, through what distance d, would the other end move? m

A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0440 m and r, = 0.300 m, respectively. A2 (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) N (b) If the smaller piston is pushed down a distance d, = 0.240 m, through what distance d, would the other end move? m

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A certain hydraulic system is designed to exert a force 405 times as large as the one put into it. (a) What must be the ratio of the area of the slave cylinder to the area of the master cylinder? (b) What must be the ratio of their diameters? (c) By what factor is the distance through which the output force moves reduced relative to the distance through which the input force moves? Assume no losses to friction.
Answer the problem question and give what is ask. Don't forget to box the final answer.
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, r, = 0.0600 m and r, = 0.140 m, respectively. (a) If a downward force of F, = 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d, = 0.176 m, through what distance d, would the other end move?
Two solid cylindrical rods support a load of P = 26 kN as shown. Determine the axial load in rod (1). 5.6 m 3.8 m O21.13 kN O22.98 kN 29.26 kN O24.71 kN O 15.50 KN B 4.6 m (2) 3.3 m
1, The force F is required to hold the pipe, Find its value, direction and location? 100 mm 3.2 m/s 150 kPa 30 150 mm S-0.86 F
In the process of changing a flat tire, a motorist uses a hydraulic jack. She begins by applying a force of 61 N to the input piston, which has a radius r1. As a result , the output plunger , which had a radius r2, applies a force to the car. The ratio r2/r1 has a value of 9.2. Ignore the height difference between the input piston and output plunger and determine the force that the output plunger applies to the car.
Rollers A and B with a weight of 600 N and 200 N, respectively, have a radius of 2 m and are placed in contact with the lateral walls and each other and kept in balance by a rope passed through the reel. Ignoring all the friction in the system; a) Find the force arising in the rope. b) Calculate the reaction forces from the lateral walls (C, D) to the cylinder. c) Find the force that the cylinders apply to each other.
The vertical face of a dam across a river has the shape of a parabola 20 m across the top and 10 m deep at the centre. Set up an integral representing the force that the river exerts on the dam if the water level is 6 m above the lowest point of the dam. There is no need to find the value of the force, only the set up of the integral is required, however, all the details are expected.
A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radii, 1 = 0.0480 m and r2 = 0.300 m, respectively. (a) If a downward force of F1 = 16.0 N is applied to the end with the smaller radius, how much force F2 would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) ]N (b) If the smaller piston is pushed down a distance d, = 0.176 m, through what distance d, would the other end move? m
Two circular platforms are attached to a fluid reservoir. On one platform rests the entire cast of Glee frozen in carbonite. A force of 7.0 N is applied downward to the empty platform with radius 8.0 m. The other platform applies a force of 7.2 N to the carbonite-frozen pop-idols. What is the radius of the platform holding the Glee cast?
Hi I need help with this question: Logs sometimes float vertically in a lake because one end has become water-logged and denser than the other. What is the average density (in kg/m3) of a uniform-diameter log that floats with 28.0% of its length above water?
Al Messenger Scribd google b My Questions | bart.. Clear selection The ratio of area of cross section of the two pistons in a hydraulic machine is 1:15. Find the force that should be applied on the narrower piston to overcome a force of 120 N on the bigger piston. 20 N 8 N 150 N O 10 N Dtatic field is 250 O O O