A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 16 mm, and the rod length was 360 mm. When the applied torque reached 254.8 N-m, a shear strain of 1780 microradians was measured in the specimen. What was the angle of twist in the specimen? Part 1 Calculate the shear stress in the specimen. Correct Answer: T= 316.97 eTextbook and Medial Part 2 Correct Use Hooke's Law to calculate the shear modulus of the specimen. answer: G= 178073.034 Part 3 eTextbook and Media. Incorrect MPa Answer: Calculate the angle of twist in the specimen. D=0.8006 MPa Attempts: 1 of 5 used Attempts: 1 of 5 used

A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 16 mm, and the rod length was 360 mm. When the applied torque reached 254.8 N-m, a shear strain of 1780 microradians was measured in the specimen. What was the angle of twist in the specimen? Part 1 Calculate the shear stress in the specimen. Correct Answer: T= 316.97 eTextbook and Medial Part 2 Correct Use Hooke's Law to calculate the shear modulus of the specimen. answer: G= 178073.034 Part 3 eTextbook and Media. Incorrect MPa Answer: Calculate the angle of twist in the specimen. D=0.8006 MPa Attempts: 1 of 5 used Attempts: 1 of 5 used

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A soft steel specimen has a BHN of 150, find the equivalent 29 tensile strength in MPa. A. 393 B. 503 C. 443 D. 533 What is the value of strain at yield point of 1-inch diameter C1030 as rolled steel in the stress-strain curve? A. 0.0012 B. 0.0015 C. 0.0017 D. 0.0022 A copper column of annular cross section has an outer diameter of 0.5 m. and is subjected to an axial loading of 5 kips. The allowable compressive stress is 2 ksi. Compute the wall thickness. A. 1.15 m B. 2m C. 0.8 m D. 1 m
The diagram shows a plot from an uniaxial test of an unknown metal. The uniaxial tensile test specimen had an original cross-sectional radius of 3.0 mm, an initial gauge length of 42 mm. At failure, the cross-sectional radius was 1.2 mm. Determine the yield strength of the unknown metal and the true stress at failure.
For some metal alloy, a true stress 345 MPa (50040 psi) produces a plastic true strain of 0.02. How much will a specimen of this material elongate when a true stress of 418 MPa (60630 psi) is applied if the original length is 500 mm (19.69in) ? Assume a value of 0.22 for the strain- hardening exponent, n
Annealed low-carbon steel has a flow curve with strength coefficient = 80,000 lb/in2 and strain-hardening exponent = 0.25. A tensile test specimen with gage length = 2.0 in is stretched to a length = 3.5 in. Determine the flow stress and average flow stress that the metal experienced during this deformation. use correct stratgy and correct E 0.55962
In the state of loading as made of brittle material tensile and compression fracture values of the exposed arm, respectively. σUT=200 MPa and σUC=800 MPa and factor of safety n=4 as it is; a) First reduce the applied forces to point B, b) By determining the critical point of the critical section and stresses Calculate it and show it on the stress element. c) Calculate the diameter of the AB part according to the Coulomb criterion. Note: Neglect the effect of cutting forces.
The results of a tensile test are: Diameter of the specimen Gauge length Load at limit of Proportionality Extension at the limit of Proportionality Maximum Load : 10mm :40 mm :80kN : 0.06mm. :100 kN Calculate ultimate tensile stress and young's modulus.
This subject is strength of materials show complete and clear solution with free body diagram and pressure diagram DONT SHORTCUT THE SOLUTION THANK YOU
please includde scetch
Qu2. (A) What is fatigue? Mention the sequence of steps involved in fatigue of a smooth specimen. Mention Four (4) factors that affect fatigue of smooth specimens, stating how each affects fatigue life (B) A very wide panel made of a material of plane-strain fracture toughness of Kic=55MPaVm was found to have a central crack of size 2.5mm. It is subjected to cyclic loading at a design (or working) stress of 690MPA and stress ratio of zero. (a) Sketch the stress-time graph of the loading cycle and determine (i) Stress Range, (ii) maximum cycle stress, (iii) stress amplitude and (iv) mean stress (b) Will the initial loading cycle cause the panel to fracture? Why or whynot? Compute the maximum allowable fatigue flaw size that can fracture the panel during the cyclic loading. (Assume that plain strain condition prevails). (c)