A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN.  If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio.  Are the numbers in line with standard numbers for Aluminum Alloy?

Q: I have a question If a sample of steel was acceptable to use at a temperature at -52 degrees c Why…

A: Brief concept introduction- Steel- It is an alloy that mainly contains iron and carbon. It has…

Q: In the figure below, a stainless steel wire is supporting a weight, W. The Yield Strength and…

A:

Q: Which of the following is the best representation of the samples' (A and B) axial strains when…

A:

Q: Calculate the percentage of steel from the figure shown below? 400 mm 8 Y 20 400 mm All dimensions…

A: Given Square RCC section 400*400 mm Reinforcement = 8# 20 mm dia bars. To Determine percentage of…

Q: The modulus of elasticity of 30mm diameter aluminum bar was 80 Gpa, calculate the strain and the…

A:

Q: A steel bar 4 inches long and having a square cross section 0.8 inches on an edge is pulled in…

A:

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: The given data is: Tensile Load on metallic bar (P) = 190 kN Diameter of bar (d) = 16 mm Length of…

Q: The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length…

A:

Q: Plot the stress-strain diagram and determine the following mechanical properties: (a) proportional…

A: Given:- Initial diameter of test specimen, D = 0.505 in Length of specimen, L = 2 in Load (lb)…

Q: Determine the yield modulus of elasticity and yield strength of an aluminum material with the…

A: The stress is taken in y-axis and strain in x-axis. From the data, stress-strain curve are being…

Q: PROBLEM 3 A tensile test is performed on a brass specimen 10mm in diameter using a gage length of…

A:

Q: A sample of metal bars with a cross-sectional area of ​​100 mm2 is subjected to a tensile test. The…

A: Given Data: The initial cross-sectional area of the metal bars is A0=100 mm2 The final…

Q: A specimen of aluminum having a rectangular cross section 10.4 mm × 12.6 mm (0.4094 in. × 0.4961…

A: So, stress can be defined as ; σ = PA P = Tension pull = 35900 A = 10.4 * 12.6 = 131.04 mm2 σ =…

Q: Compute the yield strength of a steel specimen that has an average grain diameter of 5.8 x 10-3 mm.…

A:

Q: Consider a 1 m-long bar of 2024-T81 aluminum alloy with a  20mm-diameter and the following property…

A:

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

A: Answer Based on the given data, we can calculate the minimum Elastic Modulus required for possible…

Q: A tension test was conducted for a cylindrical specimen of stain-less steel having an initial…

A: The given data is: Initial diameter, Di=15.35 mm Final diameter, Df=10.25 mm

Q: A piece of steel is said to have Young’s modulus of 29 × 106 psi. Based upon a yield strength of…

A: I

Q: Use the engineering stress strain diagram provided bclow to answer parts (A) to (H) below (the…

A: Brief concept introduction- Stress-strain curve- It represents the variation of strain (on the…

Q: A steel bar of 500 mm length is under tensile stress of 100 N/mm?. If the modulus of elasticity is 2…

A: Given data : Length (L)=500 mmTensile stress (σ)=100 N/mm2Modulus of elasticity (E)=2×1011  N/mm2

Q: 4.) A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile…

A: Length of rod (L)  = 100 mmDiameter of rod (d) = 10 mmC/s Area of Rod (A) = π4d2 = π4×102 = 78.54…

Q: 9 A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic…

A:

Q: A sample of aluminum is stretched by a 6 kip load. If the aluminum piece is 32 inches long, 2 in^2…

A:

Q: TABLE P3.19 Specimen No. Carbon Content (%) 1 2 3 0.2 0.5 0.8 Deformation (mm) Load (kN) 0.00 0.07…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 1. Titanium alloy with an elastic modulus of 107 GPa (15.5 x 106 psi) and an initial diameter of 3.8…

A:

Q: A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm When…

A:

Q: A tensile test is peformed on a brass specimen 10 mm in diameter using a gage length of 50 mm. When…

A:

Q: 90 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000…

A: Given data stress= 200 MPa rupture lifetime be 509 h

Q: A sample of aluminum is stretched by a 6 kip load. If the aluminum piece is 30 inches long, 2 in^2…

A: Stretch load (P) = 6kipLength of piece (L) = 30in. Cross sectional area (A) = 2 in.2 Determine the…

Q: 7. An aluminum rod was pulled in a tensile strength test. The reading is given in the table below.…

A: Following are the given information. Initial length =2.000 in. Final length =2.226 in.

Q: During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a…

A: Given data : Initial Length (Li)=6 inInitial area (AI)=0.32 in2Tensile load (P)=50000 lbsFinal area…

Q: A No. 8 steel rebar is tested in tension. By monitoring the load reading of the testing machine, it…

A: