-A rod 3 m long is heated from (10 to 90) °C, if the modulus of elasticity equal to 100000 MN/m2, and coefficient of thermal expansion = 0.000012 per °C, the new long of rod after expansion is 0.168 cm 0.288 cm 0.208 cm 0.348 cm 0.388 cm Other:

-A rod 3 m long is heated from (10 to 90) °C, if the modulus of elasticity equal to 100000 MN/m2, and coefficient of thermal expansion = 0.000012 per °C, the new long of rod after expansion is 0.168 cm 0.288 cm 0.208 cm 0.348 cm 0.388 cm Other:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solution
An aluminum pipe has a length of 52 m at a temperature of 6°C. An adjacent steel pipe at the same temperature is 8 mm longer. At what temperature will the aluminum pipe be 24 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×106/°C. Answer: °℃ Tf= i
42)
An aluminum pipe has a length of 68 m at a temperature of 15°C. An adjacent steel pipe at the same temperature is 10 mm longer. At what temperature will the aluminum pipe be 30 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×106/°C and that the coefficient of thermal expansion for the steel is 12.5x10-6/°C. Answer: °℃
A 0.35-m long steel rod with a round cross-section (25 mm) is resting on a frictionless surface.The rod temperature is measured to be at 10°C. The plate is then heated uniformly to 97°C.The steel has a coefficient of thermal expansion equal to 1.1*10-5 m/m/°C.a) What is the length of expansion?b) Is there a stress on the rod?c) If the rod is snugly fitted against two immovable non-conducting walls at atemperature of 15°C and the heated uniformly to 115°C, what is its length at 115°C ifthe elastic modulus of steel is 205 GPa, what is the stress induced in the bar? Tensionor compression?
An aluminum alloy cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel [E = 200 GPa; α1 = 11.7 × 10−6/°C] bolts have a diameter of 19 mm. The aluminum alloy [E = 70 GPa; α2 = 23.6 × 10−6/°C] cylinder has an outside diameter of 160 mm and a wall thickness of 9 mm. Assume that a = 700 mm, b = 810 mm, and c = 325 mm. If the temperature of this assembly changes by ΔT = 60°C, determine(a) the normal stress in the aluminum cylinder.(b) the normal strain in the aluminum cylinder.(c) the normal strain in the steel bolts.
RPSIII
The band in the figure below is stainless steel (coefficient of linear expansion = 17.3 ✕ 10−6°C−1; Young's modulus = 18 ✕ 1010 N/m2). It is essentially circular with an initial mean radius of 5.4 mm, a height of 4.4 mm, and a thickness of 0.51 mm. If the band just fits snugly over the tooth when heated to a temperature of 81°C, what is the tension in the band when it cools to a temperature of 37°C?
A liquid compressed in a container has a volume of 1 liter at a pressure of 1 MPa and a volume of 0.995 liters at a pressure of 2 MPa. The bulk modulus of elasticity of the liquid is ans. 200MPa
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature. Brass L=2 m A= 1200 mm E= 100 GPa a = 18,7 x 10-y°C B -2 m Соpper L=3 m A = 1500 mm E= 120 GPa a = 16.8 x 10-bj°C FIG. P2.108
At a temperature of 80°C, a copper tire 12 mm thick and 90 mm wide that is to be shrunk onto a locomotive driving wheel 2 m in diameter just fits over the wheel, which is at a temperature of 25°C. Determine the contact pressure between the tire and wheel after the assembly cools to 25°C. Neglect the deformation of the wheel caused by the pressure of the tire.
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown in the figure. Bar (1) is an aluminum alloy (E-10,000 ksi; u= 0,32; a= 12.5 x10°/°F] bar with a width of 3 in, and a thickness of 0.75 in. Bar (2) is a stainless steel |E-28,000 ksi; u=0.12; a=9.6x10°/°F] bar with a width of 2 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine the normal stress in bar (1) at a temperature of 450°F