An aluminum pipe has a length of 68 m at a temperature of 15°C. An adjacent steel pipe at the same temperature is 10 mm longer. At what temperature will the aluminum pipe be 30 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×106/°C and that the coefficient of thermal expansion for the steel is 12.5x10-6/°C. Answer: °℃

An aluminum pipe has a length of 68 m at a temperature of 15°C. An adjacent steel pipe at the same temperature is 10 mm longer. At what temperature will the aluminum pipe be 30 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×106/°C and that the coefficient of thermal expansion for the steel is 12.5x10-6/°C. Answer: °℃

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 6 (of 8) 6. The density of platinum is 21500 kg/m³ and that of aluminum is 2702 kg/m³. Find the ratio of the volume of 1.80 kg of platinum to the volume of 1.17 kg of aluminum.
A sufficient amount of pure copper is(4 to be heated for casting a large plate in an open mold. The plate has dimensions: length = 20 in, width=D10 in, and thickness =3 in. Compute the amount of heat that must be added to the metal to heat it to a temperature of 21500F for pouring. Assume that the amount of metal heated will be 10% more than what is needed to fill the mold cavity. Properties of the metal are: density=0.324 Ibm/in3, melting point = 19810F, specific heat of the %3D metal=0.093Btu/lbm-F in the solid state and 0.090 Btu/lbm-F in the liquid * .state, and heat of fusion = 80 Btu/lbm
solution
I need the answer as soon as possible
A 0.35-m long steel rod with a round cross-section (25 mm) is resting on a frictionless surface.The rod temperature is measured to be at 10°C. The plate is then heated uniformly to 97°C.The steel has a coefficient of thermal expansion equal to 1.1*10-5 m/m/°C.a) What is the length of expansion?b) Is there a stress on the rod?c) If the rod is snugly fitted against two immovable non-conducting walls at atemperature of 15°C and the heated uniformly to 115°C, what is its length at 115°C ifthe elastic modulus of steel is 205 GPa, what is the stress induced in the bar? Tensionor compression?
12 in. 3 ft C 4 in. 8 in. - 2014-T6 Aluminum C 86100 Bronze steel· 304 Stainless respectively. Coefficient of thermal expansion (in units of 1/F) for aluminum, bronze and copper are 12.8 x 10°, 9.6 x 10“, 10.6 x 106, respectively. draw the state of stress on a volume element. Modulus of elasticity for aluminum, bronze and copper (all in ksi) are 10 x 10, 15 x 10, 26 x 10, is 120 degree Fahrenheit, determine the average normal stress in each material when temperature reaches 100 degree Fahrenheit. For each section, The assembly has the diameters and material make-up as indicated in the figure. If it fits securely between its supports when temperature
An aluminum pipe has a length of 75 m at a temperature of 18°C. An adjacent steel pipe at the same temperature is 0.005 m longer than the aluminum pipe. At what temperature (0C) will the aluminum pipe be 0.015 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa = 23 x 10–6/°C and as = 12 x 10–6/°C, respectively.)
Answer now. Thank you.
A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.
The assembly shown in the figure consists of an aluminum tube AB and a steel rod BC. The rod is attached to the tube through the rigid collar at B and passes through the tube. The cross-sectional area of the rod is 75 mm2 and the cross-sectional area of the tube is 400 + UV in mm2, where UV is 99. A tensile load of 80 kN is applied to the rod. Take Est = 200 GPa for the steel rod, Eal = 70 GPa for the aluminum tube. Determine: (a) the displacement of end C with respect to end B (i.e., the elongation of the steel rod), (b) the displacement of end B with respect to the fixed end A (i.e., the shrink of the aluminum tube), (c) the displacement of the end C of the rod (i.e., (a) + (b)).
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, end A and end B. A collar is located in the center of the rod. The initial temp is 60 degrees C. The final temperature is 35 degrees C. Determine the force that must be applied to the collar so that the reaction at B is zero.Given:Delta T=25 degrees CE for A36 steel: 200 GPaCoeff of thermal expansion: 12(10^-6)/degree C