A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied,the normal strain in rods (1) is 2410 µm/m. Assume initial rod lengths of L₁ = 1,250 mm and L₂ = 2,000 mm. Determine the normalstrain in rod (2).(1)4₁(2)Rigid barO 975 μm/mO 1072 μm/mO 1757 µm/mO 1656 µm/mO 1506 μm/mBPL₂(1)

Answered: Image /qna-images/answer/b5f27283-a9ea-4c1c-b267-d1100184cdbc.jpg

A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 2410 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L₂ = 2,000 mm. Determine the normal strain in rod (2). (1) A (2) Rigid bar 975 μm/m O 1072 μm/m O 1757 μm/m O 1656 μm/m O 1506 μm/m B P L₂ (1)

A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 2410 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L₂ = 2,000 mm. Determine the normal strain in rod (2). (1) A (2) Rigid bar 975 μm/m O 1072 μm/m O 1757 μm/m O 1656 μm/m O 1506 μm/m B P L₂ (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe is subjected to a tension force of P = 70 kN. The pipe outside diameter is 32 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 180 GPa. Determine the normal strain in the pipe. P Select one: O a. 0.001263 mm/mm O b. 0.000535 mm/mm O c. 0.000568 mm/mm O d. 0.000794 mm/mm e. 0.001382 mm/mm O f. None
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.4 lb/in.³ is the specific weight of the material, y = 1.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 9 in. is the length of the bar, and E= 26000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar. Calculate the change in length of the bar due to its own weight. Answer: x10-6 in.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.86 in.² and bar (2) has a cross-sectional area of 0.47 in.2. After load P is applied, the strain in bar (1) is found to be 780 μe. Assume L₁-52 in., L₂=74 in., a=20 in., b=25 in., and c-33 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. Answers: (a) σ1 (b) VD=i (c) P = i L eTextbook and Media Save for Later (1) B L2 b (2) ksi, 0₂ = in. kips. i D P ksi. Attempts: 0 of 5 used Submit Answer
The Poisson ratio formula for an auxetic structure given in the figure is given as follows: H = 8 cm L = 4 cm α = 50 ° t = 5 mm The strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain on the Z axis of the structure. b) In this case, what is the strain type of the structure in the Z axis?
2.6 The truss ABC shown in the figure supports a horizontal load P₁ = 9 kN and a vertical load P₂ = 18 kN. Both bars have cross-sectional area A = 1,290 mm² and are made of steel with E= 210 GPa. a) Determine the strain energy U₁ of the truss when the load P₁ acts alone (P₂ = 0). b) Determine the strain energy U₂ when the load P2 acts alone (P₁ = 0). c) Determine the strain energy U when both loads act simultaneously. 813 mm 1524 mm P₁ = 9 kN P₂ = 18 kN
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.78 in.2 and bar (2) has a cross-sectional area of 0.32 in.2. After load P is applied, the strain in bar (1) is found to be 610 μεμε. Assume L1=50 in., L2=76 in., a=28 in., b=21 in., and c=22 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.
The bar ABC in the figure consists of two cylindrical segments. The material of the bar has the stress-strain diagram shown. Calculate the strain in segment AB caused by the 60-kN axial load. 50 50mm 40 40mm 30 60 kN 60 kN 20 10 B 500mm 400mm 0.0000 0.0005 0.010 0.015 0.020 0.025 0.030 D.035 D.040 STRAIN SSHELS
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με