A rigid bar of negligible weight is supported as shown in Fig. P-271. If W = 80 kN, compute the temperature change that will cause the stress in the bronze rod to be 35 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m-°C) for steel and 18.9 µm/ (m-°C) for bronze. Figure P-271

A rigid bar of negligible weight is supported as shown in Fig. P-271. If W = 80 kN, compute the temperature change that will cause the stress in the bronze rod to be 35 MPa. Assume the coefficients of linear expansion are 11.7 µm/(m-°C) for steel and 18.9 µm/ (m-°C) for bronze. Figure P-271

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod is made of SAE 4140 steel, compute the elongation due to a temperature change from -20°C to 140°C. TABLE 3-4 Coefficients of thermal expansion, a, for some t nd concrrete
What is the difference between static and dynamic loading.. Explain with the drawing the types of dynamic loading. b) In the figure shown, a column of AIAL 1045, cold drawn, rotates on bearings. A force of SKN is applied to it8kn . Find the modified resilience limit stress, the stress of Al-Tin Amra
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
An 1500 mm long, 43 mm aluminum square bar is rigidly supported on both ends (stress-free). Determine the stress in the bar if the temperature is raised by 153 °C. For aluminum: the coefficient of thermal expansion is 23 x 10-6/°C, G = 70 Gpa. Answer in Mpa.
Find the length of elongation of a uniform mild steel rod length of 3 m, cross-sectional area of 150 cm2 and Young's modulus of 100 GPa subjected to an axial tensile (or compressive) force F= 200 N.
A closed thin walled cylindrical vessel has a diameter D of 290 mm, a wall thickness t of 5 mm and length L of 210 mm. It is subject to an internal pressure P of 18 MPa causing circumferential stress and longitudinal stress in the vessel. Calculate the longitudinal stress due to the internal pressure. Give your answer in MPa to 3 significant figures. 00 P D 60 de OL
PROBLEM 1: Compute for the force in each member of the truss shown in FIGURE 1 if the members are made of structural steel with a Modulus of Elasticity of 200 GPa and a Coefficient of Thermal Expansion of 12x10^-6. Indicate in your solutions if the force is in tension or in compression. FIGURE 1 50 kN 100 kN 1.5 20 2.0 2.0
3. A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line. 4. The bar in Q3 is also subject to a tensile load of 15kN applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L
A rectangular filleted bar as shown in figure below is subjected to a fluctuating force F that varies from 220 N to 500 N at the end of this bar at C". Another end of this bar at 'A are fixed to the wall. This bar has a length of 130 mm from 'A' to B' and 190 mm from B' to °C. This bar is made of AISI 1050 cold-drawn steel. This bar has a thickness of 5mm, a machine surface finish and 90% reliability. AISI 1050 cold-drawn steel All units in mm F= 220 N - 500 N R3 A B, 33 30 R3 130 190 a) Because this bar has a discontimuity geometry at 'B', compute fatigue stress concentration factor, K, at this location b) Calculate all stresses acting at 'A' and B' location. Then determine which location from this two point will be the most critical. c) Determine endurance limits, S. for this part at the critical location d) Calculate safety factor, (N) of this part by using modified Goodman line theories. Give a conclusion for your answer? e) Sketch the Goodman line, Yield (Larger) line and include…
3. A mass of 102kg falls 12mm directly onto the end of a bar 25 mm in diameter and 1.5m long. If E for the material is 207 GPa, find the instantaneous stress produced.
STRENGTH OF MATERIALS A steel bolt and sleeve assembly are shown in the figure. The nut is tightened up on the tube through the rigid end blocks until the tensile force in the bolt is 40kN. If an external load of 30 kN is then applied to the end blocks, tending to pull them apart, estimate the resulting force in the bolt.