A rigid bar is carried by deformable steel and aluminum rods as shown in the figure. If P = 122 kN, a = 10 m, and b = 3 m, determine the ratio of the axial deformation of steel to aluminum. (no unit) $ a steel L=3m A = 3200 mm^2 E = 200 GPa b P aluminum L=4m A = 4600 mm^2 E = 160 GPa

A rigid bar is carried by deformable steel and aluminum rods as shown in the figure. If P = 122 kN, a = 10 m, and b = 3 m, determine the ratio of the axial deformation of steel to aluminum. (no unit) $ a steel L=3m A = 3200 mm^2 E = 200 GPa b P aluminum L=4m A = 4600 mm^2 E = 160 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 3000 kgf tensile load is applied on a steel bar of 3.25 cm diameter. When the same load is applied…

A: Given data: P=3000 kgfDsteel=3.25 cmEsteel=2.1×106 kgf/cm2Eal=0.7×106 kgf/cm2

Q: A steel bar of 50 mm × 50 mm square cross-section is subjected to an axial compressive load 200 kN.…

A: Steel bar 50 mm x 50 mm, Axial compressive load P = 200 kN Length L = 2 m, E=160 GPa Deformation = ?

Q: The aluminum machine part is subjected to a moment of 75 kNxm. Determine the bending stress created…

A: Solution:Given: The moment acting on the section is M=75N.m which is sagging, so the topmost fiber…

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch The cross-sectional area of…

Q: A 10 cm diameter solid alumin Assume that L=0.5 m. The yiel a) Normal stress due to bending caused…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: a. Determine b. Determine c. Determine normal force in rod AC, NAC. normal force in rod AB, NAB.…

Q: 3. Two rods are assembled with area, modulus of elasticity, and coefficient of thermal expansion as…

Q: A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

A: Given data: Allowable stress in steel =120 MPa Allowable stress in bronze=60 MPa a=1.8 m b=1.3 m…

Q: Consider a square aluminum element of 3in. Dimensions as shown in figure below. If a force is…

A: Poisson's ratio (μ) = 0.33 Deformation along y-axis (δLy) = 0.02 in. Determine the strain in the X…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

A rigid bar is carried by deformable steel and aluminum rods as shown in the
figure. If P 122 kN, a 10 m, and b = 3 m, determine the ratio of the axial
deformation of steel to aluminum. (no unit)
a
steel
L=3m
A = 3200 mm^2
E = 200 GPa
b
P
aluminum
L=4m
A = 4600 mm^2
E = 160 GPa
23

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In any case ,The final answer must be correct. Please include the Diagram
A circular bar of magnesium alloy is 390 mm long. The stress-strain diagram for the material is shown in the figure. 70 63 56 49 O (MPa) 42 35 28 21 14 7 0.002 0.004 0.006 0.008 0.01 The bar is loaded in tension to an elongation of 2.34 mm, and then the load is removed. Hint: Use the concepts illustrated in the figures below. (Assume the curve in the figure above is linear between (0, 0) and (0.001, 28), and curves with a gradually decreasing slope otherwise.) F В E F Loading CD Loading Residual Elastic strain recovery (a) What is the permanent set of the bar (in mm)? 2.184 X mm (b) If the bar is reloaded, what is the proportional limit (in MPa)? 55 X MPa
The stress in a steel bar is given as 25,0000 kN/m² and length of the bar is 50 m. Calculate the shortening of the bar if E = 2.14 × 108 N/mm²
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
The following shaft is composed of two materials, both rigidly bonded. The data is provided in the table: Determine: The maximum torque that can be applied based on the maximum stresses of each material. The total deformation of the shaft with the torque from the previous section. The maximum torque that can be applied if the maximum deformation of the shaft is 2.50 rad.
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?
A round steel alloy bar with a diameter of 19mm and a gauge length of 76mm was subjected to tension, with the results shown in Table. Using a computer spreadsheet program, plot the stress–strain relationship. From the graph, determine the Young’s modulus of the steel alloy and the deformation corresponding to a 37kN load.
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
A rod is composed of 3 segments shown in the figure and carries the axial loads, P1=120KN and P2=50KN. If the walls are rigid, determine the stress of bronze, aluminum, and steel in MPa.
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
Knowing that a 0.02in gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11ksi, (b) the corresponding exact length (2 decimal places in 103 inches) of the aluminum bar. 0.02 in. 14 in. Bronze A = 2.4 in² E = 15 × 106 psi a = 12 x 10-6/°F 18 in. Aluminum A = 2.8 in² E = 10.6 × 106 psi a = 12.9 x 10-6/°F