A reinforced concrete beam is 225 x 650 mm (b x d). The tension steel consists of 2H16 and 2H20 bars and the compression steel is 2H12 bars. Determine the ultimate moment capacity of the section, assuming fck = 25 N/mm2 and fyk = 500 N/mm2. The cover to centre of steel is 50mm.

Q: Two L4 x 3 x -in. steel angles are welded together to form the column AB. An axial load P of…

A:

Q: P B 8M 6M

A:

Q: 1- A W 5300*101 of Steel Section (f,= 345 MPa & fu= 450 MPa) is used as simply supported beam with a…

A: Given:W530×101Sx=2290×103mm3Zx=2620×103mm3Lb=3mmLp=1.94mLr=5,70mL=15mLp<Lb<LrLesser of either…

Q: ANALYZE THE STRUCTURE USING PORTAL FRAME METHOD. COMPUTE: RECUNDED. AXIAL LOAD OF AD AINT ALL MOMENT…

A:

Q: The simply supported beam consists of a W21x 44 structural steel wide-flange shape [E = 29,000 ksi;…

A:

Q: 3-2 Determine the ultimate load of the structure. The ultimate moment of the material is Mu. FP /3…

A: For any beam when ultimate load is applied then under the ultimate load, ultimate moment we can…

Q: 5. A beam has a width of 300mm and effective depth of 540mm. d 60mm. It is reinforced with 8-25mm…

A:

Q: te tw

A:

Q: 3. The rigid bar ABC and EFG are supported by pins at A and G. The vertical rods are made of steel…

A: Deformation of bar takes place due to Load applied Change in temperature Self weight of bar…

Q: 200 mm

A:

Q: Lohposiu piGM uith eapedf 4) X: tio to lowingi a cenchridal Xgas 150 200

A:

Q: Question 27 A built up l-section is formed from plates welded together as shown in the figure. It is…

A:

Q: H.W/ By using ASD and LRFD methods, find a light section W12xw of A992 steel material of member BC…

A:

Q: 4. A beam has a width of 300mm and effective depth of 540mm, d' 60mm. It is reinforced with 4-25mm…

A: A beam is defined as a horizontal structural element to resist vertical or laterally applied loads.…

Q: - For below cantilever beam derive the length of elastic-plastic zone F, L

A: GIVEN, There is a cantilever beam  having length L and which is subjected to a point load of…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength :Yield strength of an element is a maximum stress an element or component can bear…

Q: A portal frame P Q R as shown in figure has a fixed support at P and free end at R. A point load of…

A: For a portal frame PQR as shown below,fixed support at P and free end at Rpoint load of 3 kN is…

Q: Show FBD and complete solution.    Determine the horizontal and vertical components at A and C.…

A:

Q: For the isolated T-section shown below, Determine the reduced nominal moment capacity, oMn, and…

A:

Q: Compute the location and maximum value of elastic equation curve for the beam loaded as shown. a

A:

Q: 1-2-8 The four struts at A, B, C, and D all have the same cross-section. Find the minimum diameter…

A: Given:- Ultimate normal stress=58 ksiFactor of safety=3 To find:- Minimum diameter

Q: A reinforced concrete beam is 225 x 650 mm (bxd). The tension steel consists of 2H16 and 2H20 bars…

A:

Q: Calculate the ultimate moment capacity of the beam whose width is 400mm and effective depth d = 700.…

A: Given:Beam width, b=400 mmEffective depth of the beam=700 mmsteel area in compression =1953 mm2steel…

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: A rigid beam ABC supports a linear distributed load with maximum value q while supported by a pin at…

A:

Q: N A F q C B D X 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed…

A: a = (40+40)/50 = 1.6m  q = (40+25)/20 = 3.25KN/m

Q: In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 80…

A: This question is related to Design concrete structure. There is Option (A) 200 mm is correct answer.

Q: 0:Design the steel reimforcement for flexural for the beam shown m the kN fig.below The dead load on…

A: if the size of beam is known and area of reinforcement is need to design then their is 2 cases  1-…

Q: Determine the design moment capacity of the beam with the following sections properties. Given: d…

A:

Q: Girder AB. Assume Use Fy = 50 ksi and select a shape for that the floor slab provides continuous…

A:

Q: Given the beam properties: b = 250 mm h = 550 mm steel cover = 60 mm f'c = 28 MPa fy = 345 MPa %3D…

A:

Q: is made from aluminum (EA10.6x106 psi) and . segment B is made from steel (Es=29×10° psi) If w= 4.7…

A: Given Length of the beam = 15 ft w = 4.7 kips/ft

Q: The section of a reinforced concrete T-beam has d= 500mm bf = 600mm t = 100mm bw =…

A: Data Given: d= 500mm bf = 600mm t = 100mm bw = 300mm. diameter of bar = 28 mm # of bars (n) = 12 Fy…

Q: Required information The rigid bar AD is supported by two steel wires of -in. diameter (E = 29 × 106…

A: Given data  Load Span length  Diameter  Modulus of Elasticity

Q: Design a beam

A: