A refrigeration system requires 1.5 kW of power for a refrigeration rate of 4 kW. (a) What is the coefficient of performance? (b) How much heat is rejected in the condenser? (c) If heat rejection is at 313.15 K (409C), what is the lowest temperature the system can possibly maintain?

Q: I at 351 v.v42L i) Calculate the temperature distribution at the middle and rate of heat floe at the…

A: Given,

Q: Air at 300 kPa and an average of 450 K is being heated as it flows through a rectangular conduit of…

A: The rate of heat transfer for unit area is called as heat flux normal to the direction heat flowing.…

Q: A pot 25 cm in diameter is placed on the stove. The pot is made of stainless plate (k = 15 W / [m °…

A: Given: Thermal conductivity, k = 15 W/m.0C Pan thickness, x = 0.6 cm = 0.006 m Dia of the pan, D =…

Q: Determine the average convection heat transfer coefficient in a pipe (diameter d = 8 cm, length L =…

A:

Q: (b) An electric kettle with a 3kW heater element is used to boil water. The kettle has a stainless…

A: To determine the temperature at the center of the wire (T_max) and the convective heat transfer…

Q: The energy transfer between the hot fluid and cold fluids is brought about by their complete…

A: We have to answer which type of heat exchanger is used where the hold and cold fluid is direct…

Q: A vessel with a paddle agitator and no baffles is used to heat a liquid at 37.8degC in this vessel.…

A: Given Inside diameter of the vessel, Di=1.22 m Diameter of the agitator, Da=0.406 m Speed of the…

Q: Liquid food is heated in a tubular heat exchanger.  The inner pipe wall temperature is 110 ° C.  The…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: The exhaust duct from a heater has an inside diameter of 114.3 mm with ceramic walls 6.4 mm thick.…

A: Given data: Inside diameter = 114.3 mm Ceramic walls 6.4mm, the average k = 1.52W/mKThermal…

Q: One kilogram of air is heated reversibly at constant pressure from an initial state of 300 K and 1…

A: For a detailed solution, please see the attached files.

Q: In a desert chemical plant, the operator wishes to store chilled water underground in a spherical…

A:

Q: The pipe is 6 m long with an inner radius of 70 mm, an outer radius of 80 mm, and is made of…

A: The rate of heat transfer through the pipe wall is to be calculated.

Q: Q3) After a long time in service, a counterflow oil cooler is checked to ascertain if its…

A: To Find  The heat reduced due to fouling

Q: Water available at 24 C is heated by a heating element having 30 mm outside diameter and 0.4 m…

A: Cp=4180J/kg.∘C k=0.64W/m∘C density(r)=988kg/m3 μ=0.55×10-3N-S/m2 Ts=80∘C length=0.4m do=30mm=0.03m…

Q: Q2-A straight fin of triangular profile is constructed of copper with a thickness of 2.1 mm. The fin…

A: Given: A straight copper fin of triangular profile. Thickness of the fin, t = 2.1 mm = 0.0021 m…

Q: Problem 1 A pipe containing steam with an inner diameter of 200 mm is surrounded by an insulating…

A:

Q: 1. An experimental engine has a quartz window in the cylinder head that is 2.5 cm thick. During…

A: The heat transfer process is a process in which the molecules are moved from the region of higher…

Q: Q2. An annulus consists of the region between two concentric tubes having diameters of 3 cm and 5…

A:

Q: Q/ The heat transfer rate q over a surface is given by dT 9 = -KA= dy where k = thermal conductivity…

A: Given  K = 0.0125 J/ s .m. k Area  A = 2.5 m2 At y = 1.5

Q: Q5) A cube of aluminum 10 cm on each side is initially at a temperature of 300 °C and is immersed in…

A:

Q: 7.1 What is condenser ? 7.2 What are the functions of a condenser in a thermal power plant? Give the…

A: A condenser is an essential component in thermal power plants, converting exhaust steam back into…

Q: The heat-transfer rate through the walls and roof of the house is 0.72 kW for each kelvin of…

A: GivenThere is a reference to heat pump, so we are dealing with a problem on heating arrangement for…

Q: Calculate the amount of heat (in kJ/mol) needed to remove to cool air at a rate of 15 kmol/min from…

A:

Q: The rate of heat transfers through a wall of thickness 20 cm having k = 5 W/m K, inner surface…

A: Given: L = 20cm = 0.2m A = 1m2 T1 = 60oC T2 = 30oC k = 5W/mk