A rectangular loop of wire is moving toward the bottom of the page with a speed of 0.020 m/s. The bottom part of the loop is outside the region. The field strength inside the region is 2.4 T and the magnetic field outside the region is and the magnetic field outside the region is zero. The width of the loop is 0.080 m and the length is 1.0 meter. What is the current induced in the wire if the resistance of the loop is 0.12 ohm

A rectangular loop of wire is moving toward the bottom of the page with a speed of 0.020 m/s. The bottom part of the loop is outside the region. The field strength inside the region is 2.4 T and the magnetic field outside the region is and the magnetic field outside the region is zero. The width of the loop is 0.080 m and the length is 1.0 meter. What is the current induced in the wire if the resistance of the loop is 0.12 ohm

Similar questions

in the figure below, a square loop with 10 turns that is 10.0 cm on a side has a magnetic field pointed into the page that is decreasing at the rate of 1.0 T/s. a) What is the magnitude of the emf generated in the wire and what is the direction of the resulting current along the top side of the loops? b) Assume the self inductance is 4.1 x 10-4 H and the wire’s resistance is 11 Ohms. How much energy is stored by the inductor while the magnetic field is decreasing at this fixed rate?
a flat circular coil with 150 turns, a radius of 6.00 * 10^-2 m, and a resistance of 0.30 is exposed to an external magnetic feild that is directed perpendicular to the plane of the coil. the magnitude of the external magnetic feild is changing with time at a rate of 0.80 T/s. a. find the magnitude of the induced current. b. find the magnitude of the induced magnetic feild B(induced) at the center of the coil.
loop. The magnetic field in this case is A vertically oriented square loop of copper wire falls from rest in a region in which the field B is horizontal, uniform, and perpendicular to the plane of the loop, into a field- free region, see (Figure 1). The side length of the loop is s and the wire diameter is d. The resistivity of copper is PR and the density of copper is pm. If the loop reaches its terminal speed while its upper segment is still in the magnetic-field region, find an expression for the terminal speed. Part I Find the emf. Express your answer in terms of the variables s, B, and v. ▸ View Available Hint(s) E = Ο ΑΣΦ Submit Figure Square loop of copper wire. Above this line: Buniform and horizontal Below this line: B=0 s = side length X X 1 of 1 X X X XBX X dwire diameter ↑ s = side length Part J Complete previous part(s) Part K Complete previous part(s) Part L Complete previous part(s) Part M Complete previous part(s) Part N Complete previous part(s) EVALUATE Uterminal Part…
A circular loop in the plane of a paper lies in a 0.65 T magnetic field pointing into the paper. The loop's diameter changes from 21.5 cm to 6.8 cm in 0.52 s . What is the magnitude of the average induced emf?
A 0.300 mm diameter copper wire makes up a 85.0 turns, 7.90 cm diameter coil. There is a magnetic field parallel to the axis of the coil. If the induced current in the coil is 4.80 A, what is the rate of change of the magnetic field? 58.5 T/s 4.97×103 T/s 3.20×10-6 T/s 0.222 T/s
Suppose a magnetic field B(t) oscillates with frequency w. A circular loop of copper lies perpendicular to the magnetic field. The radius of the circular loop is r. a. Write down an expression for the magnetic field as a function of time. Determine the induced emf & in the loop of wire and use this to calculate the current generated in the loop as a function of time. b. What is the power dissipation in the wire as a function to time? Make a sketch of this function. What is the average power Pave dissipation in the wire? Hint: what is the average value of the function you sketched? C. Recall that power is a rate of energy transfer, and that power dissipated by a resistor leads to a change in the thermal energy of the material (in this case the copper wire). We can relate a change in thermal energy to a change in temperature by AT where M is the total mass and c ΔΕth Mc is the specific heat capacity of the material (see page 526 for details). Find an expression for a dT - differential…
A square coil of wire has 10 turns and an area of 20 cm^2. The square coil is located in a variable magnetic field whose behavior is shown on the graph. The magnetic field is directed at an angle of 45° relative to the normal to the plane of the square coil. a. What is the average emf induced in the coil in the time interval from t=7.50 s to 10.0 s? b. If the wire has a resistance of 0.75 Ω determine the induced current for the interval from part (a)?
Q8.5 A circular plastic core is wrapped with a 22.0 m-long copper wire, with a diameter of 0.0200 mm and resistivity of 1.68×10-8 9-m, coiled 88 times, and its ends are linked to create a closed circuit. A magnetic field that increases at a constant rate of 12.0 mT/s, parallel to the coil's axis. Calculate the rate at which the wire produces thermal energy
A circular coil of 50 turns and radius 8.0cm is placed with its plane oriented at 90 degrees to a magnetic field of .20 T. the field is now increased at a steady rate, reaching a value of .80T after 3.0 seconds. What emf is induced in the coil? a. 40V b. 0V c. 0.20V d. 0.0040V e. 2010V
A square coil of wire with a side length of 10 cm is looped around 10 times. The coil sits in an increasing magnetic field. The magnetic field increases linearly from 1T to 2T within 5 seconds. What is the induced emf of the coil? a. 0.02 V b. 2 V c. 20 V d. 200 V
A flat circular coil with 100 turns has a radius of 0.04 m and a resistance of 0.5 ohms. It is exposed to a changing magnetic field that is perpendicular to the coil. The rate at which the magnetic field is changing is ∆B/∆t=0.782(T/s). a. Find the emf (voltage) induced in the coil. b. What is the current in the coil? c. Sketch a picture of the scenario and, based on your drawing, show the direction of the induced current PLEASE SHOW ALL WORK!! Thank you!!
A conducting wire loop of radius 12 cm, that contains a 4.0-2 resistor, is in the presence of a uniform magnetic field of strength 3.0 T that is perpendicular to the plane of the loop. If the magnetic field is turned off in a time of 0.50 s, what is the current induced in the loop? a. 52 mA b. 68 mA O c. 95 mA d. 117 mA O e. 168 mA