A rectangular gate 1.6 m wide is used as a partition as shown. One side has linseed oil filled to a depth of 10 m. The other has two fluids-castor oil (0.96) over water. If z'= 3m, determine the total hydrostatic pressure acting on the right side of the gate.

A rectangular gate 1.6 m wide is used as a partition as shown. One side has linseed oil filled to a depth of 10 m. The other has two fluids-castor oil (0.96) over water. If z'= 3m, determine the total hydrostatic pressure acting on the right side of the gate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A semi-circular gate of diameter "d" and radius "r" is submerged in a liquid and has its diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is 2m from the surface and radius is 2 m. b. Compute the location of the center of pressure if the top of the gate is 2m from the surface and radius is 2 m. c. Compute for the hydrostatic force on one side 4r 13n hg CG. CP.
Determine the magnitude and location of the total hydrostatic force acting on the 2m x 4m gate shown in the figure. Ans. F= 733.16kN, 1.844m from the bottom of the tank parallel to the gate
Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 30 cm above the pipe B. The height of oil in right limb is 50 cm. Also, the mercury level difference is found in right limb as 90 cm. Find the pressure difference between these two pipes in kPa. Also find the pressure equivalent in water head in mm. The difference of pressure between two pipes (PA-PB) (Unit is in kPa) ? Equivalent to Water head in mm ?
Question 4. The flowrate of the flow is 0,20 m/s in a pipe placed on a horizontal plane. The pipe diameters are as 0.41 m and 0.28 m for Di and D2, respectively. Find the resultant force *(kN) acting to the pipe by the flow. The gauge pressure at (1) is P1 =280 kN/m2. (y= (1) 10KN/m³) Figure 4
PROBLEM 3: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids-castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (1llustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. 1m hinge Linseed Oil (SG = 0.938) Castor Oil (SG = 0.96) 10 m 2 m water The hydrostatic force due to linseed oil F1.
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Solve with clear solution.
A water main line is composed of two pipes connected in series, pipes AB and BC. Pipe AB is 500 m long and 30 cm in diameter while pipe BC is 800 m long and 20 cm in diameter. Point C is 10 m higher than point A. The pressure at point C is 3 kg per square cm higher than the pressure at point A and the coefficient for minor head losses due to contraction and enlargement are 0.40 and 0.25 respectively. Determine the discharge and flow direction on the water main line using Darcy-Weisbach formula with f = 0.02 for all pipes. Draw approximately the EGL and HGL.
Consider the pressurized horizontal pipe network shown below. Pipe 2 is arranged in parallel with Pipe 3. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 10 cfs and the pressure head at Node A is yA = 180 feet. The temperature of the water is 60° F. a) Determine the flow in cfs in Pipe 2. b) Determine the flow in cfs in Pipe 3. c) Determine the friction head loss hric in feet in Pipe 1. d) Determine the friction head loss hfic in feet in Pipe 2. e) Determine the friction head loss htric in feet in Pipe 3. f) Determine the friction head loss hfric in feet in Pipe 4. g) Determine the pressure head ys in feet at Node B. h) Determine the pressure head yc in feet at Node C. i) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Pipe (inches) (feet) Friction (cfs) head Нead factor f Kpipe loss (feet) Node (feet) 1 16 500 0.012 10 A 180 12 1000 0.014 B 10 1000 0.015 16 500 0.020 10 D Pipe 2 Node Node Node…
UT. LEUMASARY Water flows at a rate of (0.5 m³/s) round a (50) contracting pipe bend which lies in a horizontal plane. The diameter at the entrance is (700 mm) and at the exit (500 mm) as shown in figure (7). If the pressure at the entrance is (200kPa. ), Determine the magnitude and direction of the force exerted by the fluid on the bend. d = 500mm out d=700mm Figure (7 in 50
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3