A rectangular building 250 m and 130 m is to be laid out with a 30 m long steel tape. If during standardization the tape is found to be 30.03 m, the correct length and width to be laid out should be O a. 249.97 m by 129.97 m O b. 249.87 m by 129.75 m O. 249.75 m by 129.87 m O d. 250.25 m by 130.13 m

A rectangular building 250 m and 130 m is to be laid out with a 30 m long steel tape. If during standardization the tape is found to be 30.03 m, the correct length and width to be laid out should be O a. 249.97 m by 129.97 m O b. 249.87 m by 129.75 m O. 249.75 m by 129.87 m O d. 250.25 m by 130.13 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the correct length of a line 256.32 m long measured using a 50 m steel tape at 30°C. The steel tape was calibrated at 18°C.
Please draw profile and longitudinal cross-section
In the value of data shown: Take X = 621.22 What is the value of LEC?
A square prism of base edge 40 mm and height 50 mm is resting on its base. Develop its lateral surface on gridsheet.
15. You are to lay out two points that are exactly 200.000 m apart. Field conditions indicate that standard conditions apply except the measured temperature is 27°C from 20°C temperature during standardization. Determine the correct distance to be laid out
what is the total area? use DMD method
A 20 cm x 20 cm x 40 cm block weighs 50 N when fully submerged in water.
Q2). Calculate volume of cut and fill, the elevation of natural ground shown on all nodes and design elevation is equal to 103 m, all dimension and elevations are in meter. hi h, 101 102.5 W₂ 104.2 ha 108.10 98.45 412 100.5 Wy -10 m 102.5 hey 105.7 12 97.35 99.80 101, hs 104 hi 10 m ha 104 106.5 hi Thi
Given: A1= 3400, A2=800, A3=706.85834, A4=176.71458 Y1=42.5, Y2=26.666, Y3=52.7324, Y4= 62.5 X1=20, X2=53.333, X3=52.7324, X4=17.5 Total Area: 4730.14376 ȳ=40.604 x̄ (x-bar) = 30.6224 Please, I want you to solve the: 4.) Moment of Inertia About the x-axis Ix 5.) Moment of Inertia About the y – axis Iy 6.) Polar Moment of Inertia about the axes Jo 7.) Moment of Inertia About the centroidal x-axis Ix note: In locating the centroid of the entire section, Varignon's Theorem. Varignon's Theorem locates the centroid of a composite body. I hope you will use the formulas I will be giving.
3.8 sq ft=___ sq in.
h₂ Q2). Calculate volume of cut and fill, the elevation of natural ground shown on all nodes and design elevation is equal to 103 m, all dimension and elevations are in meter. 101 102.5 W₂ 104.2 12 108.10 98.45 412 100.5 hy -10 m 102.5 he 105.7 h2 97.35 99.80 101, 104 hi 10 m h2 104 106.5 hi Thi
A 105m by 105m lot is to be divided into 9 equal square sections. The elevations of the ground surface at each corner of the square section are as follows: A=7.3m E-7m 1-7.3m M=7.3m B=7.5m F=6m J=7.3m N=6.9m C=7.2m G-6.5m K-7.1m 0-6.3m D=7.3m H=7.6m L=6.5m P=7.8m Find the volume to be excavated if the ground surface is to be leveled to elevation 4.7m. Round your answer to 3 decimal places.