10. A line measured with a 30-m steel tape was recorded as 325.70 m. If the tape is found to be 30.05 m long during standardization, the correct length of the line is a. 325.16 m b. 325.70 m c. 327.45 m d. 325.44 m e. 326.24 m 11. A rectangular building 250.0 m (L) x 130.0 m (W) is to be laid out with a 30-m long steel tape. If during standardization the tape is found to be 30.03 m, the correct length and width to be laid out should be a. 249.75 x 129.87 m b. 250.25 x 130.13 m c. 249.87 x 129.75 m d. 250.00 x 130.00 m e. 249.97 x 129.97 m

10. A line measured with a 30-m steel tape was recorded as 325.70 m. If the tape is found to be 30.05 m long during standardization, the correct length of the line is a. 325.16 m b. 325.70 m c. 327.45 m d. 325.44 m e. 326.24 m 11. A rectangular building 250.0 m (L) x 130.0 m (W) is to be laid out with a 30-m long steel tape. If during standardization the tape is found to be 30.03 m, the correct length and width to be laid out should be a. 249.75 x 129.87 m b. 250.25 x 130.13 m c. 249.87 x 129.75 m d. 250.00 x 130.00 m e. 249.97 x 129.97 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Compute and illustrate the cross-sectional area. (Use trapezoidal rule) 2. Given the chainage data…

Q: The distance between points is exactly 100 ft. This measurement is read correctly on steel surveyors…

A: To determine the actual distance for the measured distance. Given, Measured distance, say L =…

Q: Calculate the amount of vertical displacement that will occur at point E with the VIRTUAL METHOD.…

A: A = 10 cm2 = 1000 mm2 E = 100000 MPaDetermine the vertical displacement of joint E using virtual…

Q: Moment of inertia of a triangle having base 15 m and height 6 cm about edge opposite to base is

A: Given: Triangle having base, b=15 cm height, h=6 cm To find. Moment of inertia about edge opposite…

Q: 1. A square piece of land 60m x 60m is to be leveled down to a level coinciding to elevation zero.…

A: Excavation depth = average elevation - zero Determine Volume of cut, V = grid area * average…

Q: 3. A student was asked to make 365.24 m long line using a 25-m tape that is 0.0024 m too long. What…

A: Hi there!! since you have asked multiple questions,as per our honour code we will solve the first…

Q: In Figure 1.1, determine the distance between point A and B which spans a wide and deep river. Lines…

Q: a1/ In the shown triangle below, length of line AB =160m, Find the length of lines AC and BC? Note…

Q: Determine the correct length of a line 256.32 m long, measured using a 50-m steel tape at 38 deg. C.…

A: Coefficient of thermal expansion for steel = 11.6*10-6 /0C Measured length (l) = 256.32 m Length…

Q: An unknown line was paced by a surveyor and gathered the following data: 489, 482, 489, and 483. He…

A: Given: The paced data for the unknown line is 489, 482, 489, and 483. The distance of the new line…

Q: AREA BY TRIANGLES. Given in the accompanying tabulation are quantities which were measured for a…

A: To find area of the field using triangle method

Q: 2. The following values were determined in a series of tape measurements of a line: 920.58,…

Q: Find station and eleva THE PARABOLA. GIVEN:

A: PVCSTATION=PVISTA-L2PVCsta=1000-8002=6+00PVCELV=PVIELV-g1L2PVCelv=71.5-0.03×8002PVCelv=59.5ftEquatio…

Q: 30 kN 50 kN B C D 1m 3 m 2 m Figure P-403

A: We have to solve the above given beam using integration method with slope intercept as per the solid…

Q: A 50m steel tape is used to measure line AB. The measured length of line AB is 521.16 meters. Given…

Q: 34. Calculate the area by M.D method, if the value of m1, m2, m3 are given as 233.4 m, 12.78 m,…

Q: A 50-m tape was used to measure distance AB as 945.60m. The tape was discovered to be 50.075m after…

A: Given data, Designated tape length l = 50 m Actual tape length la = 50.075 m Length to be measured L…

Q: .b\ In measuring a straight line, you come across: 1.a pond, 2. a tall building. Describe how you…

A: Obstruction while chaining and ranging

Q: he distance between two points is found to be 220.45 m using a 100 m tape that is found to be X…

A: l×L=L'×l'where,l=designated tape length,L=true length of line,L'=wrong length of line,l'=actual but…

Q: When measured towards southward, latitude is negative. * O True False

Q: BACKSIGHT FC a(0) RR(m) | VD(m)| s(m) a( .35 12.02 1.35 .85 9.26 1.42 1.95 .67 7.14 1.25 1.76

Q: A line is laid out using a 50-m tape. The standard error of each tape length laid out is assumed to…

A: To Determine :- Question 1. The standard error of the length of the line. Question 2. The correct…

Q: - tapes 50 m and 30 m v and found 723.41 m and .42 m respectively. Com gth of 50 m tape, if you -…

A: Given data - Length of tape1 = 50 m Length of tape2 =30 m Measure Length with tape1of AB = 723.41m…

Q: State the principles of proportionality and superposition in developing unit hydrograph.

A: A hydrograph is a graph or plot that depicts the rate of water flow as a function of time at a…

Q: Determine the correct length of a line 256.32 m long measured using a 50 m steel tape at 30°C. The…

A: Given data Length of measured line (L) = 256.32 m Length of steel tape (l) = 50m Temperature at…

Q: To determine the horizontal distance between Q and R, a tacheometer was used and was placed at P.…

A: Given: Stadia intercept for Q = 0.320 m Stadia intercept for R = 0.210 m Angle QPR = 61°30’30”…

Q: Determine the magnitude of the resultang.

A: Given that:

Concept explainers

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.

Question

10. A line measured with a 30-m steel tape was recorded as
325.70 m. If the tape is found to be 30.05 m long during
standardization, the correct length of the line is
a. 325.16 m
b. 325.70 m
c. 327.45 m
d. 325.44 m
e. 326.24 m
11. A rectangular building 250.0 m (L) x 130.0 m (W) is to be
laid out with a 30-m long steel tape. If during
standardization the tape is found to be 30.03 m, the correct
length and width to be laid out should be
a. 249.75 x 129.87 m
b. 250.25 x 130.13 m
c. 249.87 x 129.75 m
d. 250.00 x 130.00 m
e. 249.97 x 129.97 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A 30-m tape having a standard length of 30.005 m is to be used to lay-out a building that has plan dimensions of 150.000 by 270.000 m. What horizontal measurements must be made on the ground in the field to perform this layout? 2. A 50-m tape of standard length has a mass of 0.02kg/m, with a cross-sectional area of 0.04 sq. cm. It has a modulus of elasticity of 2.10x106 kg/sq. cm. The tape is of standard length under a pull of 5.5 kg when supported throughout its length and a temperature of 20°C. This tape was used to measure a distance between A and B and was recorded to be 458.65m. long. At the time of measurement, the pull applied was 8 kg. with the tape supported only at its endpoints and the temperature observed was 15°C. Assuming the coefficient of linear expansion of the tape is 0.0000116m/°C. Compute for the true length (with the combined effects of tension, sag, and temperature) of the measured line AB.
please provide clear & complete solution. thanks!
James rides his bike from his training camp (T) to the beach (B) 15km away on a bearing of 053°. a. Complete a diagram to show the given information. b. Mark and calculate the bearing of T from B. c. Calculate the distance James travelled south. d. Calculate the distance James travelled east.
The table below contains the information about the cross - section. If the formation width is 10 m, find the area of the cross - * .section Cross – section L CL R С 3.05 | С 3.65| С 2.45 С 2.95 C 2.65 C 3.45 11.10 7.30 3.5 8.6 11.8 47.46 m2 O 50.65 m2 O 45.82 m2 48.91 m2 O
15. A rectangular field was measured using a 100 m tape which was actually 10 cm too short. The recorded area was 2500 sq.m. Calculate the true area of the field. c. 2550 sq.m a. 2495 sq.m b. 2505 sq.m d. 2496.70 sq.m
Using parallelogram law, determine the magnitude of the vector F. 200 Ib A. 295.44 lbs B. 254.94 Ibs C. 244.95 lbs D. 294.45 lbs O A
An unknown line was paced by a surveyor and gathered the following data: 489, 483, 488, and 482. He then laid out a 100m line and paced it several times. The following data were gathered: 143, 144, 139, 136, and 141. Determine the length (m) of the line.