A steel tape is 100.00 ft long and has a weight of 0.0225 lb/ft and is used to measure a line from A to B in two segments (one full tape length and one partial tape length), supported at the ends only for each of the two segments. The recorded

Q: Q1// Test the following DE for exactness: y (cos'x+y sin x) dx + cos x (sin x cos x+ 2y) dy = 0 اختر…

A: We have, y(cos3x+ysin x)dx+cos x(sin x cos x+2y)dy=0 A differential equation of first order and…

Q: magnitude of maximum deflection  b) Rotation at right support in degrees c) Rotation at left support…

A: Given:- udl=5kN/mpoint load=2kNTo find:-a) Location and magnitude of maximum deflection  b) Rotation…

Q: A)Convert the "basis weight" of 38 of a facing into the "ream weight" . There is no more extra data…

A: Given- Basis weight =38 To Find- Ream weight

Q: Consider the beam shown in Egure 1) Take E-29(10) kxi. I-120 in Figure 100 10A 30 100 1001 Part B…

A:

Q: indicated to the horizontal neutral axis. The girder is also supporting a mass of 5000kg 30kN 20kN…

A:

Q: | ZAO O "l zain IQ 10/10 find the strain( €) in x-axis only. if Poisson ratio=0.25, E= 200 .GPa 14…

A: Given data Loads Area of cross sections Modulus of Elasticity  Poissons ratio

Q: Experimental, Values, N Trials Computed Values, N Percent Error RA .6659kg 6.5258 N 6.5333 N 0.11…

A:

Q: Replace the force system acting on the post by a resultant force(Figure 11. Figure 1 m 500 N 0.5 m…

A:

Q: The least count of a dial test indicator is 0.01 mm which is a direct measurement device with 100…

A: Finding out true and false.

Q: Linear measurement can be measured through either direct method, indirect method, or electronic…

A: Well As we know that, In the surveying,Linear measurements can be determined by using any of 3…

Q: A 30 m tape weighs 12 g/m and has a cross sectional area of 0.020 cm?. It measures correctly when…

A: Given data: L=30 m W=12 g/m  A=0.020 cm2 Standard pull=85 N Field pull=85 N Standard…

Q: Q: The lengths of the sides of a plot of land were measured and they were equal to (200 x 300 m)…

A: Given:- The size of the plot = 200×300 m The nominal length of the tape = 30 m  The real length of…

Q: Question / Find Ax at Joint C, and O by using Virtual Work Method, if you know E = 200 GPa, I=…

A:

Q: A tape 100m long, it's cross sectional area in 0.0585 cm', the apparent length of which was found to…

A: Given that:                     Nominal length of tape, l = 100mArea of cross section, A = 0.0585…

Q: Figure STS 003 shows a pole acted upon by three forces. Select the correct response: 4500.0 3842.2…

A: Given: Required : Value of couple in equivalent couple force system

Q: Use virtual work to find the vertical.displacement under the 30 kN load and the rotation at c. 20 kN…

A:

Q: Solve using nevilles method at x=6 asap

A:

Q: Given: A circular with dimensions and series of loads as shown Required: the elastic deformation in…

A: step 1-

Q: A line was determined to be 2,651.56 meters when measured with a 30 m. steel tape supported…

A:

Q: A beam of square cross-section is bent in the plane of its diagonal. A cut is made at top and bottom…

A: A beam of square cross-section is bent in the plane of its diagonal.A cut is made at the top and…

Q: While measuring three segments of a base line, the following data were obtained. Segment No. Length…

A:

Q: 4. A 30-m steel tape weighing 1.75 kg is of standard length under a pull of 4.55 kg, supported for…

A: Given data in question  30 m tape Standard pull Measured pull Elastic modulus Unit weight To find…

Q: What is the reaction force at the fixed support at O? (Figure 1) Enter the x, y, and z components of…

A: Given : F = 260 i - 130 j   N Reaction forces at fixed support O

Q: D Shaft is getting twisted. Shaft diameter is D and Material Shear Modulus is G. How much Torque…

A: The answer is found to be Torque T = 62.66 N.m For explanation please refer the attached solution,…

Q: Which among the following determines the direction of closing error? O a. Tan δ = Σ/ΣΟ b. Tan 8 =…

A: A closing error is a distance that failed to close the end of the traverse line with its starting…

Q: Distinguish between the following terms: a. Sensitivity and detection limit b. LOQ and limit of…

A: Detection limit, as they state very well in another part of the text, is the lowest detectable level…

Q: horizontal and vertical components of the hinge force at C as it acts upon BD.

A:

Q: 8. Distances d1, d2, and d3 on a calibration baseline were measured. dz d, The following results…

A: Basic data given: d1 : 95.49 m + 0.03 m d2 : 100.73 m + 0.03 m d1 : 196.18 m + 0.06 m

Q: A line was determined to be 2,682.13 meters when measured with a 20 m. steel tape supported…

A:

Q: A 30-m steel tape standardized at 20°C and supported throughout under a tension of 5.45 kg was found…

A:

Q: ΕΧΑMPLΕ 1) A circular bar having 200 mm? area is subjected to axial loads as shown in Fig „Find the…

A:

Q: A 100 m tape weighing 30 N is suspended between the two ends under a standard pull of 180 N. The…

A: Given: A 100 m tape weighing 30 N. The tape is suspended between the two ends under a standard pull…

Q: Q2 calculate the Vertical movement of point A 1 41 t Steel wire D = 25 m E = 20X1D" +4 Wi 2 4 20KN…

A: Determine the vertical movement of point-A.