A rectangular beam has width 12 in. and effectivedepth 17.5 in. It is reinforced with four No. 9 (No. 29) bars in one row. If f, = 60,000 psi andf. = 4000 psi, what is the nominal flexural strength, and what is the maximum moment thatcan be utilized in design, according to the ACI Code?

Solution: Given Data: Beam width bw=12 inEffective width=d=17.5 inArea of reinforcement=As=4…

Answered: A rectangular beam has width 12 in. and…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the internal force acting on member DF, EF and EG? Please dictate if its in compression or in tension. Complete solutions please.
A steel bar of rectangular cross section (2.5 in. x 3.2 in.) carries a tensile load P (see figure). 3.2 in. 2.5 in. Ⓡi The allowable stresses in tension and shear are 15,500 psi and 7,350 psi, respectively. Determine the maximum permissible load P max lb (in lb).
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
Figure 1 shows the cross-section of a heavily welded I-section steel column under axial compression. The yield stress of the steel section is 300 MPa. (a) Check the slenderness of the flanges and webs. (b) Determine the effective and gross areas of the cross-section. (c) Determine the design axial capacity of the cross-section. 380 E 10 425 -8 Figure 1. Cross-section of the rectangular hollow section steel column (Units: mm)
The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A rectangular beam has width 12 in. and effective depth 17.5 in. It is reinforced with four No. 9 (No. 29) bars in one row. If f, = 60,000 psi and f. = 4000 psi, what is the nominal flexural strength, and what is the maximum moment that can be utilized in design, according to the ACI Code?