A rectangular beam 350 mm wide and effective depth of 500 mm is to be designed as subjected to an ultimate moment of 750 kN-m. The concrete strength to be used is 28 MPa and the yield strength of reinforcement of 415 MPa. If compression bars are need, it is placed 70 from the extreme compression face. Determine the amount of compression reinforcement. Select the correct response: O O 1,534 1,543 1,720 1,702

A rectangular beam 350 mm wide and effective depth of 500 mm is to be designed as subjected to an ultimate moment of 750 kN-m. The concrete strength to be used is 28 MPa and the yield strength of reinforcement of 415 MPa. If compression bars are need, it is placed 70 from the extreme compression face. Determine the amount of compression reinforcement. Select the correct response: O O 1,534 1,543 1,720 1,702

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
Determine the additional longitudinal reinforcements (mm2) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
1. The strain profile of the section below with compression reinforcement was calculated with a computer program. All dimensions are to center of the reinforcements. Material properties: (a) (b) (c) Concrete, f'e = 4.0 ksi Steel, fy = 60.0 ksi Is the section tension controlled? What is the strength reduction factor (p)? Check if the forces in the section are in equilibrium. Do not correct them if they are not in equilibrium. What is the nominal moment resistance of the section? (4) #9- #5@4" (5) #11. (5) #11 -24"- SECTION 3" 3" 3" 48" 0.015 0.01 0.005 Strain diagram eps ecu epst 10.035 0.01 @lowest reinforcing steel Strain Profile 0 10 20 30 40 50 60 -0.005
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
Based on Eurocode 2 (2004), the flexural capacity of the section shown below Is 60 kN.m for the concrete cylinder strength (fem) of 40 MPa. Estimate the flexural capacity of the section if the concrete cylinder strength (fcm) becomes 30 MPa. 150 mm Lever arm (z) = 180 mm
A rectangular concrete beam has a width of 300 mm and an effective depth of 550 mm. The beam is simply supported over a span of 6 m and is used to carry a uniform dead load of 25 KN/m and a uniform live load of 40 kN/m. Assume fic= 21 MPa and fx = 312 MPa. Compression reinforcement if necessary shall be placed at a depth of 80 mm from the extreme compression concrete. Which of the following most nearly gives the required number of 25mm diameter tension bars? A. 6 B.7 C. 8 D. 9
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
CAN SOMEONE HELP ME SOLVE THIS REINFORCED/PRESTRESSED CONCRETE PROBLEM. USE NSCP 2015 A concrete beam has a width of 304.8 mm and an effective depth of 495.3 mm. It is reinforced with 14.194 cm2 steel bars with fc′ = 17,237.5 kPa (n = 10). Determine the flexural stresses caused by a bending moment of 84.1 kN·m
A singly reinforced rectangular beam 350 mm wide and 450 mm deep is reinforced with 2-16-mm-diameter bottom bars enclosed with 10-mm-dia stirrups covered with 40 mm of concrete.Calculate the tensile steel strain compatible with concrete strain of 0.003. Use f'c = 26 MPa and fy = 370MPa. Express your answer in 4 decimal places
Using IS 456