A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles(d)calculate the water horsepower.

Q: uation and graphical representation and compare the results (take 45o increment ,N= 3000 r.p.m).

A:

Q: A pump has the following parameters N= 2133.5 RPM, Ns = 40 RPM, D = 37.1 cm and is used to pump…

A: As per the guidelines, I can solve only 1st three sub-parts. For rest parts, please re-post again.…

Q: 1. A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The…

A: Given:Suction pipe diameter, ds=260 mm=0.260 mDischarge pipe diameter, dd=150 mm=0.150 mWater flow…

Q: . centrifugal pump rotates at 750 rpm. Water (p=1000) inters the impeller normal to blades (á = 0°)…

A:

Q: A 15 in. diameter fan operates at 1600 rpm and develops a head of 6 in. of water and delivers 120…

A:

Q: outlet (1) fixed divider 30 60 14. A jet of water with a velocity of 18 m/s has a discharge of 60…

A:

Q: air fan has a bladed rotor of 12 in outside diameter and 10 in inside diameter. The height of each…

A:

Q: A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is…

A:

Q: Figure  shows two points a half-period apart in theoperation of a pump. What type of pump is this ?…

A: The working is as the centre rod moves to the right, the check valves allows A to fill and B to…

Q: centrifugal pump discharged 20 L/s against a head of 17 m when the speed is 1500 rpm. The diameter…

A:

Q: A horizontal jet of water issues from a nozzle 7.5 cm diameter under an effective head of 67.5 m and…

A: Given data: The diameter of the nozzle, d = 7.5 cm. The effective head, h = 67.5 m. Calculate the…

Q: A centrifugal pump works against 10 m at 1000 rpm. varies are curved back at an angle of 30° to the…

A:

Q: B-A pump has the following parameters N=2133.5 RPM, Ns = 40 RPM, D= 37.1 cm and is used to pump…

A:

Q: A centrifugal pump with 30 cm diameter impeller is rated at 30 lps against a head of 24 m when…

A:

Q: m shown for the turbine to produce 20 kW. Neglect Friction in your calculations (1) Q=10.75m3/s (2)…

A: The power rate of turbine is given by ρ = ρQgHWhere H= 30 m            ρ= 1000 kg/ m3            g=…

Q: Q4(b) A water turbine model is constructed at ratio of 1:8 with power system of 10 kW at speed of…

A:

Q: Calculate the piston travel, velocity, and acceleration for an engine with R= 50 mm and Irod%3D170…

A:

Q: Q5/ A centrifugal pump impeller runs at 1500 rpm & has internal & external diameters of 0.2 n & 0.4…

A: A centrifugal pump is a mechanical device that moves a fluid by transferring rotational energy from…

Q: A Francis water turbine has a runner of 1m outer diameter. It rotates at a speed of 160 rpm, flow…

A: Given  Flow velocity, Vf = 2.8 m/s               Head, h = 10 m             Speed, N = 160 rpm Find…

Q: 4 m of water, and each of the three elbows ha uces the diameter by a factor of 0.60 (60% o ntraction…

A: Given Data The pipe diameter after the pump is:Dafter=1.8 cm The pipe diameter before the pump…

Q: A centrifugal pump rotates at n = 1160 rpm. Water enters the blades radially. The outlet radius is…

A: Given:Pump speed, n=1160 rpmOutlet radius, r2=9 in=912ft=0.75 ftBlade width, b2=2 in=212ft=0.1667…

Q: could you please help me calculate the maximum height of the jet , Hj in metres please

A:

Q: 2. The figure shows a pipe reducing section that is bolted on to the end of a pipe. Water flows…

A:

Q: data apply: Inlet blade velocity is 20 m/s. Vu1=21 m/s; Vr1=10 m/s. At the exit, V2 is purely axial…

A:

Q: A course in Turbomachinery. ..Lecturer: Dr.Naseer Al-Janabi 21 125 J/kg and Total to Total…

A: Fluid Mechanics: It is a branch of physics in which concerns with mechanics of fluids and forces…

Q: A certain SSSF control volume with a single inflow and outflow and has an inflow speed V₁ = 200…

A:

Q: A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow…

A: We are to find the actual head generate by a pump having radial vanes  and a manometric efficiency…

Q: A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow…

A: Given data: Write the expression to calculate the discharge.

Q: At a point A in a pipe line carrying water, the diameter is 1 m, the pressure is 98 KPa and the…

A:

Q: • The firefighter holds the hose 1 m off the ground. What is the speed of the flow as it leaves the…

A: according to bartleby policy, answering first 3 subparts only.

Q: This course CHide block A centrifugal pump with the following impeller dimensions is used to pump…

A:

Q: A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is…

A: Given DataN=1400 rpmr2=0.21mβ2=158°Cr2=4m/s

Q: Water flows through a pipe and into a section that allows water to exit through Area 2 and Area 3…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.