Situation 1:A pump draws 24 liters per second of water fromreservoir C and lifts it to reservoir D as shown in figure.The head lost from C to 1 is 3 times the velocity head inthe 150-mm suction line and the head lost from 2 to D is25 times the velocity head in the 100-mm discharge line.1. What is the power delivered by the pump to thesystem in hp?А. 73.212. What is the pressure head at point 1 in meters ofB. 65.93 C. 83.87 D. 79.62water?A. 19.62 B. 23.56 C. 32.67 D. 16.583. What is the pressure heat at point 2 in meters of water?A. 234.89 B. 321.67 C. 271.42 D. 178.43DEl. 240 mC El. O m1 2El. – 20 m150 mmPump100 mm

Given- Discharge (Q)=24 l/secDischarge (Q)=0.024 m3/sec

A pump dráws 24 litérs per second of water fr reservoir C and lifts it to reservoir D as shown The head lost from C to 1 is 3 times the velocit the 150-mm suction line and the head lost from 25 times the velocity head in the 100-mm disch 1. What is the power delivered by the pump to

A pump dráws 24 litérs per second of water fr reservoir C and lifts it to reservoir D as shown The head lost from C to 1 is 3 times the velocit the 150-mm suction line and the head lost from 25 times the velocity head in the 100-mm disch 1. What is the power delivered by the pump to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Oil (SG = 0.88) flows in an inclined pipe at a rate of 6 ft³/s as shown in the figure below. If the…

Q: Determine the pressure head at point 1 and point 2 (in meters). Also, determine the power delivered…

Q: Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage.…

A: The given data is shown below: Specific gravity=0.75Pressure at A=142 kPa

Q: FRESHMEN What is the value of F required to balance the weight of the cylinder if the weight of the…

Q: An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter…

A: Let's suppose, the suction side as point A and the discharge side as point B, and the vertical…

Q: The 50 cm diameter pipe shown below transfers water from reservoir A to a pressure turbine and…

A: Given Data Determine the power (in HP) from the turbine (P).

Q: Two geometrically similar pumps are running at 1200 rpm speed (both). If one pump has impeller…

Q: Situation # 4: The pump shown draws water from the reservoir A at elevation 10m and lifts it to…

Q: The Power (P) required to drive the pump depends upon the diameter (D), the angular velocity (0),…

Q: The centrifugal pump blades are 20 mm in depth at the outlet. The impeller is 250 mm in diameter and…

A: A centrifugal pump's impeller features backward-facing blades that are angled at 30 degrees to the…

Q: water pump at elevation 46 m. is used to bring up 250 gpm of water from a river (elev. 45 m.) to…

A: Discharge is 250 gpm Elevation of reservoir is 100 m

Q: C) In a cylinder-piston arrangement shown (D₁ = 100 mm), the piston is moving downwards at Vp = 0.5…

A: step 1-

Q: Two homogeneous pumps runs at a same speed of 500 rpm. Pump A has diameter 50 cm and discharges 0.6…

A: Given- Same speed=500 rpm Diameter=50 cm discharge=0.6 m3/s, Net head=50 m, Pump B discharge=0.3…

Q: The large tank shown in the figure contains water and shoots it up using a pump connected to its…

A: In the given figure a pump placed at the bottom of the tank of depth 20 m raised the liquid to 27 m…

Q: Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1…

A: (B) 135.20 hp

Q: 64 A pelton wheel works under a head of 400 m. Frictional loss through the pipe flow is limited to…

A: A Pelton wheel turbine-Head of wheel = 400 mLimitation of frictional loss = 10%The coefficient of…

Q: Water

Q: EXAMPLE: A line is required to provide 20 L/s of water from a dam to a high level storage tank…

A: To design the water line to provide 20 L/s of water from the dam to the high-level storage tank…

Q: Given a system of pulley below, Block A has a mass of 50 kg. At point P it is recorded to have a…

Q: ExamPle 11.1 Basic Difference Between a Pump and a Turbine GIVEN The rotor shown in Fig. E11.la…

A: Given- A rotor is given. The inlet and outlet velocities along with the angular velocities are…

Q: A channel of rectangular section, 9ft wide, is discharging water at a rate of 71034gal/min with an…

A: "Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at…

Q: A sharp-edged circular nozzle with a cross-sectional area of 10 cm2. Water flows from it under the…

A: Actual velocity calculation:…

Q: Elevation- 42.7 m Elevation- 274m L-608 m D-20 cem L-304 m Da 20 cm -Elevation- 122m Figure 2:…

Q: sp. he pump in the system is 78% efficient and is rated 185 kW. Determine the energy added by he…

Q: A fixed control volume has three one-dimensional boundary sections, as shown. The flow within the…

A: Rate of change of the energy of the system which occupies the (er) at this instant Where,…

Q: Liquid 1 SG X y Liquid 2 SG: --- ----- Both the top of the tank and the end of the slanted tube are…

Q: With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized…

A: Given:- The chamber-pipe system is given The fixed diameter of BCDEF pipe = 40 cm The elevation of…

Q: ELEV. 130m 2 B L = 1000m D = 200mm f = 0.023 L = 1500m D = 250mm L = 300m ELEV. = 40m f = 0.02 D =…

Q: The ball B of negligible size rolls through the tube such that at the instant shown in (Figure 1) it…

A: Given: To find: Part A: Velocity of the ball if the tube has an angular velocity, ω = 3 rads/s and…

Q: Ex.6: In a centrifugal pump having a manometric efficiency of 0.7 and having the outer diameter…

A: Centrifugal pumps are used to transport fluids by the conversion of rotational kinetic energy to the…

Q: If the inner diameter of the penstock that deliver water form the dam to the hydroelectricpower…

Q: (Bernoulli/continuity) Water flows into a large tank at a rate of 0.011 m³/s as shown in the figure…

Q: Water at 20°C is transported from 2m high tank to a another 9m high tank through 25m long parallel…

A: parallel pipe is given so discharge is different and and head loss will be equal for both given…

Q: The pump is powered by a 30 kW motor. If the pump is 82% efficient, determine the pressure rise…

A: V1 = 40 m/s d1 = 4 cm =0.04 m d2 = 8 cm = 0.08 m effective power P = 0.82 x 30000= 24600 W

Q: Please reply ASAP. Will rate immediately. Which of the following gives the horizontal reaction at…

Q: A pump is rated with 80% efficiency and requires 4hp of power. The power output results to a…

A: Efficiency of the pump = QHρ367 P2 ρ=1000 kg/m3 P2= 2.9828 KW Velocity = 5ft/s=1.524 m/s Average dia…

Q: A channel of rectangular section, 9ft wide, is discharging water at a rate of 71034gal/min with an…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A pump drawing water from a reservoir and discharging it into the atmosphere at point B. The…

Q: A nozzle of inner radius 1.06 mm is connected to a hose of inner radius 9.05 mm. The nozzle shoots…

Q: t’s required to determine the height (H) when the flow is 120 L/s ؟

A: Flow rate Q = 120 L/s Area A = π4*0.252 = 0.049 m2 V = 1200.049 = 2.45 m/s Calculation of 'Re' Re…

Q: KĻ = 0.5 Diameter = 10 cm Kµ = 0.4 Tank 1 5 m 25 m 28 m Diameter = 20 cm Diameter = 15 cm Tank 2 10…

A: Applying Bernoulli equation b/w 1 and 2:…

Q: 7) Bernoulli equation deals with the law of conservatio (a) mass (b) momentum (c) energy (d) work…

A: As per guidelines we need to answer only first question so please repost rest questions separately.

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

100%

Situation 1:
A pump draws 24 liters per second of water from
reservoir C and lifts it to reservoir D as shown in figure.
The head lost from C to 1 is 3 times the velocity head in
the 150-mm suction line and the head lost from 2 to D is
25 times the velocity head in the 100-mm discharge line.
1. What is the power delivered by the pump to the
system in hp?
А. 73.21
2. What is the pressure head at point 1 in meters of
B. 65.93 C. 83.87 D. 79.62
water?
A. 19.62 B. 23.56 C. 32.67 D. 16.58
3. What is the pressure heat at point 2 in meters of water?
A. 234.89 B. 321.67 C. 271.42 D. 178.43
D
El. 240 m
C El. O m
1 2
El. – 20 m
150 mm
Pump
100 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows through a pipe at 150 L/s changes gradually in diameter from 165 mm at point M to 473 mm The and that м is respective pressures point m higher point at N. 4.3 than N. at point M and N are 72 kPa 49.8 kPa. a. Determine the head lost of the pipe. b. Determine the total energy at point N with datum at point M. c. Determine the total energy at point M with datum at point M.
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure . The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. 1. Compute the Power delivered by the pump in kw ( A. 79.07 , B. 48.10 C. 13.08 , D. 57.23) 2. Compute the Pressure head at point 1 in m. ( A. 85.96 , B. 19.74 C. 245.09 , D. 45.90) 3. Pressure head at point 2 in m. ( A. 104.51 , B. 246.67 C. 57.84 , D. 12.69)
6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the energy added by the pump. 160mm w EL. 200m 200mm 9 El.150m Oif. Sp.gr.=(0.82
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and has coefficients of velocity and discharge of 0.98 and 0.96, respectively. The nozzle is supplied from a 60cm pipe in which the water approached the nozzle with a total head of 330m. Compute the following: a. Energy per second delivered by the jet to the turbine. b. Energy measured in hp lost in passing through the nozzle.
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
Where did this 101.3 over 76 coming from? Its not on the given. Here is the picture.
An oil pump is drawing 18 kW of electric power while pumping oil with density 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet diameters of the pipe are 8 cm and 11 cm, respectively. If the pressure rise of oil in the pump is measured to be 250 kPa and the motor efficiency is 95 percent, determine the mechanical efficiency of the pump. Take the kinetic energy correction factor as 1.05. Pump 8 cm D.cm ΔΡ = 250 kPa 18 kW Motor Oil 0.1 m³/s The mechanical efficiency of the pump is %.
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
I need the answer to the question in fluid mechanics
the 9.63. When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe, the head loss is 36 m (120 ft). Calculate the flowrate. 9.64. A pump of what power is required to pump 40 1/min of crude oil from a tank of surface elevation 12 to one of elevation 18 through 450 m of 75 mm pipe, if the oil is at (a) 25°C, (b) 40°C?
Please solve in detail.